Radically modified Fender 800, conversion to rods instead of cables but needs finished, for health reasons I can't finish it. if interested please call me at 303-901-1449 for answers.if it don't go like it is I will be parting out soon. $550.plus shipping
NOTE- The case shown in Picture was sold with another steel. the case I have to ship it in is and older case for shipping.
Fender 800
- Al Risbeck
- Posts: 1167
- Joined: 15 Feb 2005 1:01 am
- Location: Iowa, USA
Fender 800
Last edited by Al Risbeck on 9 Aug 2018 8:52 am, edited 3 times in total.
Mullen Discovery, GK mb200 with Eminence EPS-15C, Fender steel King with Eminence EPS-15C,Nashville 400 amp, with EPS-15C,Evans FET500 with Peavey 1501 BW Goodrich L10K V.P.(2),Goodrich L120, Bose L1 PA with ToneMatch 4 Mic control board
-
- Posts: 4773
- Joined: 21 Mar 2005 1:01 am
- Location: new brockton,alabama (deceased)
?
al, doe,s the levers work as they are or would all that have to be finished?....thanks jack
- Al Risbeck
- Posts: 1167
- Joined: 15 Feb 2005 1:01 am
- Location: Iowa, USA
800
Jack left knee levers work, right knee one need to be re designed as there is too much travel required. All rods need redone and I’m my opinion timed with springs and collars like an Emmons p/p it will come with Emmons four hole bellcranks and swivels and other extras. All parts that needed it have been re-chrome, legs etc.
Mullen Discovery, GK mb200 with Eminence EPS-15C, Fender steel King with Eminence EPS-15C,Nashville 400 amp, with EPS-15C,Evans FET500 with Peavey 1501 BW Goodrich L10K V.P.(2),Goodrich L120, Bose L1 PA with ToneMatch 4 Mic control board
-
- Posts: 4773
- Joined: 21 Mar 2005 1:01 am
- Location: new brockton,alabama (deceased)
?
al, doe,s the pedals work as they should, and are they setup in emmon, also are the knee levers set up emmons with e,s on the left knee?....thanks jack
-
- Posts: 4773
- Joined: 21 Mar 2005 1:01 am
- Location: new brockton,alabama (deceased)
?
al, doe,s the levers work as they are or would all that have to be finished?....thanks jack
- Al Risbeck
- Posts: 1167
- Joined: 15 Feb 2005 1:01 am
- Location: Iowa, USA
800
It is Emmons setup, pedals are about the same stiffness as a cable rig, right knee levers need re designed.
Mullen Discovery, GK mb200 with Eminence EPS-15C, Fender steel King with Eminence EPS-15C,Nashville 400 amp, with EPS-15C,Evans FET500 with Peavey 1501 BW Goodrich L10K V.P.(2),Goodrich L120, Bose L1 PA with ToneMatch 4 Mic control board
-
- Posts: 1073
- Joined: 25 May 2005 12:01 am
- Location: California, USA
Near complete project
Countless hours put onto plans and fabricated components..at a giveaway dispossess is what I see. If you are any kind of ' knuckle-skinner' with half of Al's resolve inside you, this would be a short distance to complete. So sorry health issues have to interrupt, Al. I know that curse quite well. Best Wishes. Jon Z.
- Mike DiAlesandro
- Posts: 1503
- Joined: 8 May 2010 7:36 am
- Location: Kent, Ohio
- Contact:
- Al Risbeck
- Posts: 1167
- Joined: 15 Feb 2005 1:01 am
- Location: Iowa, USA
Fender 800
SOLD pending payment
Mullen Discovery, GK mb200 with Eminence EPS-15C, Fender steel King with Eminence EPS-15C,Nashville 400 amp, with EPS-15C,Evans FET500 with Peavey 1501 BW Goodrich L10K V.P.(2),Goodrich L120, Bose L1 PA with ToneMatch 4 Mic control board