Third string Gauge .011 vs .015.
Moderator: Shoshanah Marohn
-
- Posts: 94
- Joined: 28 Sep 2014 6:58 pm
- Location: Phoenix, AZ
Third string Gauge .011 vs .015.
Worn out subject I realize after searching Forum BUT, I have enough strings to last my lifetime due to buying sets to get the 3rd string .011. My question is, can I substitute a .015 without problem and a noticeable difference. Thanks.
Last edited by Gerald Keller on 28 Aug 2023 5:41 pm, edited 1 time in total.
Justice " The Judge"
Sho-Bud LDG
Desert Rose
Speedy West
Show Pro
Other Expensive "Stuff"
Sho-Bud LDG
Desert Rose
Speedy West
Show Pro
Other Expensive "Stuff"
- Jerry Overstreet
- Posts: 12622
- Joined: 11 Jul 2000 12:01 am
- Location: Louisville Ky
-
- Posts: 21192
- Joined: 16 Feb 1999 1:01 am
- Location: Glen Burnie, Md. U.S.A.
- Larry Dering
- Posts: 5076
- Joined: 17 May 2013 11:20 am
- Location: Missouri, USA
-
- Posts: 94
- Joined: 28 Sep 2014 6:58 pm
- Location: Phoenix, AZ
- Larry Dering
- Posts: 5076
- Joined: 17 May 2013 11:20 am
- Location: Missouri, USA
My opinion is no. I believe this has been tried and failed to take the tension. Plus balance problems. I usually buy single. 011 by the dozen. You can get them shipped free from some venders. I get sets from musicians friend in the Rogue brand. I also buy from Just Strings in the bulk package but shipping is charged unless you buy quite a bit.
A 013 or 015 will snap in a heartbeat when you step on that B pedal.
Kevin Maul: Airline, Beard, Clinesmith, Decophonic, Evans, Excel, Fender, Fluger, Gibson, Hilton, Ibanez, Justice, K+K, Live Strings, MOYO, National, Oahu, Peterson, Quilter, Rickenbacher, Sho~Bud, Supro, TC, Ultimate, VHT, Webb, X-otic, Yamaha, ZKing.
- Richard Sinkler
- Posts: 17067
- Joined: 15 Aug 1998 12:01 am
- Location: aka: Rusty Strings -- Missoula, Montana
If you truly mean .015 and not .0115, you better wear a welders mask as a .015 would probably break before it even got to pitch (G#). I wouldn't want to be anywhere near that guitar when That string exploded.
Carter D10 8p/8k, Dekley S10 3p/4k C6 setup,Regal RD40 Dobro, NV400, NV112 . Playing for 53 years and still counting.
- Dave Mudgett
- Moderator
- Posts: 9648
- Joined: 16 Jul 2004 12:01 am
- Location: Central Pennsylvania and Gallatin, Tennessee
To the original poster - surely, you mean a 0.0115, not 0.015. Your 5 is in the wrong decimal position. Although not exactly standard, 0.0115 is not an unusual gauge for 3rd string G#4. The possible choices arePost subject: Third string Gauge .011 vs .015.
0.0110 (standard 0.011, which is what most PSG sets come with)
0.0115
0.0120 (0.012)
The approximate tensions for a typical 24.25" scale pedal steel tuned to G# and then stretched to A are
Code: Select all
Gauge Tension at G#4 Tension at A4
0.0110 31 pounds 35 pounds
0.0115 34 pounds 38 pounds
0.0120 37 pounds 41 pounds
0.0130 43 pounds 49 pounds
0.0140 50 pounds 56 pounds
0.0150 57 pounds 65 pounds
I think 0.012 at around 40 pounds for A4 is pushing it, but some people make it work. I have tuned 23-25" scale length slide guitars to Open A = A E A C# E A and it is a very difficult proposition for anything above a 24" scale, regardless of the top string gauge. I have broken a lot of strings trying to tune Strats up to Open A. I am confident that 0.150 would snap long before it got up to A4. And even if it didn't snap, the tension would be ridiculous. To give an idea of the scale of things, a typical electric guitar string has a tension of less than 20 pounds. For example, a .010 gauge string on a 24.75" scale Les Paul is about 17 pounds, and on a 25.5" Strat is about 18 pounds. Pedal steel strings are under higher tension. 35 pounds for a 0.011 3rd string is typical - most strings have significantly lower tension than this - and a lot of people do snap .011 3rd strings.
We talk about it frequently here. But 60+ pounds is absurd.
Of course, you can try a .015. I think Richard's idea of a welder's mask is good. And you're putting a helluvalotta tension on the finger. I wouldn't do it myself. Is this just to use some .015 strings you have and avoid buying some of the correct gauges? Penny-wise and pound-foolish, IMO.
- Jerry Overstreet
- Posts: 12622
- Joined: 11 Jul 2000 12:01 am
- Location: Louisville Ky
Not sure what you're asking. I thought you meant .0115, but now I don't know.
As to a .013 for a third: I bought an older Zum several years ago and, just for fun, I used a gauge to measure all the string diameters before I changed them.
To my surprise, it had a black balled D'Addario 13 ga. string on the 3rd. I double and triple checked it but it was def. a 13.
I normally use a .012 gauge, but curious if it would stand another one, I replaced it with another 0.13 gauge. Talk about taut, yeah, it was scary but it didn't break.
I played that guitar for 5 yrs. or more and always used a 13 at the 3rd spot. I was nervous about it for a while, but got used to it and never had a problem with unusual breakage.
There is another player here that also used a 13 on a Zum successfully, but I don't know of any others.
I posted it about it here on the froum somewhere.
I'd consider this a phenomenon and would be curious to know what that actual string tension was tuned up to A with a pedal. [Edit: Overlooked the chart above]
I've never tried it since with any other guitar, but since it was already in use on that Zum, I just kept on using it just out of stubborness and curiosity, besides I liked the fatter tone.
I would not recommend you try it though.
As to a .013 for a third: I bought an older Zum several years ago and, just for fun, I used a gauge to measure all the string diameters before I changed them.
To my surprise, it had a black balled D'Addario 13 ga. string on the 3rd. I double and triple checked it but it was def. a 13.
I normally use a .012 gauge, but curious if it would stand another one, I replaced it with another 0.13 gauge. Talk about taut, yeah, it was scary but it didn't break.
I played that guitar for 5 yrs. or more and always used a 13 at the 3rd spot. I was nervous about it for a while, but got used to it and never had a problem with unusual breakage.
There is another player here that also used a 13 on a Zum successfully, but I don't know of any others.
I posted it about it here on the froum somewhere.
I'd consider this a phenomenon and would be curious to know what that actual string tension was tuned up to A with a pedal. [Edit: Overlooked the chart above]
I've never tried it since with any other guitar, but since it was already in use on that Zum, I just kept on using it just out of stubborness and curiosity, besides I liked the fatter tone.
I would not recommend you try it though.
- Dale Rottacker
- Posts: 3513
- Joined: 3 Aug 2010 6:49 pm
- Location: Walla Walla Washington, USA
- Contact:
IF you put a .015 gauge string in the 3rd spot, you better wear Kevlar gloves when playing cause when it snaps, and it WILL, you'll lose a finger.Gerald Keller wrote:If not a .015 and if a .012 works, which I don't have, will a .013 be close enough. Thanks
Personally I use a .012 and wouldn't go bigger than that. I love the heftier feel and tone of it and if it does snap it WILL draw some blood, but I won't need stitches or need that finger reattached like I would when that .015 pops.
Dale Rottacker, Steelinatune™
*2021 MSA Legend, "Jolly Rancher" D10 10x9
*2021 Rittenberry, "The Concord" D10 9x9
*1977 Blue Sho-Bud Pro 3 Custom 8x6
https://msapedalsteels.com
http://rittenberrysteelguitars.com
https://www.telonics.com/index.php
https://www.p2pamps.com
https://www.quilterlabs.com
*2021 MSA Legend, "Jolly Rancher" D10 10x9
*2021 Rittenberry, "The Concord" D10 9x9
*1977 Blue Sho-Bud Pro 3 Custom 8x6
https://msapedalsteels.com
http://rittenberrysteelguitars.com
https://www.telonics.com/index.php
https://www.p2pamps.com
https://www.quilterlabs.com
- Erv Niehaus
- Posts: 26797
- Joined: 10 Aug 2001 12:01 am
- Location: Litchfield, MN, USA
It sounds like you've been stealing replacement 3rd strings from full sets, and now have a bunch of partial sets hanging around. Here's a suggestion: Instead of trying to substitute questionable gauges for your 3rd string (and making the necessary adjustments to your pulls) why not buy some single .011's or .012's to complete the sets you cannibalized?Gerald Keller wrote:I have enough strings to last my lifetime due to buying sets to get the 3rd string .011. My question is, can I substitute a .015 without problem and a noticeable difference.....
If not a .015 and if a .012 works, which I don't have, will a .013 be close enough. Thanks
1980 MSA Vintage XL S-10, 1975 Session 400
1972 Dobro model 66s
Derby SD-10
Tom McDonough
1972 Dobro model 66s
Derby SD-10
Tom McDonough
- Larry Dering
- Posts: 5076
- Joined: 17 May 2013 11:20 am
- Location: Missouri, USA
-
- Posts: 3296
- Joined: 2 May 2008 3:15 pm
- Location: Columbia, Mo. U.S.A.
-
- Posts: 94
- Joined: 28 Sep 2014 6:58 pm
- Location: Phoenix, AZ
Third String Guage
Rather than buy another complete set or wait for shipment, I was trying to use what I had. Went to Guitar Center here in Phoenix and bought out their bulk inventory of .011 and .012 or a total of 10. Thanks for everyone’s comments.
Justice " The Judge"
Sho-Bud LDG
Desert Rose
Speedy West
Show Pro
Other Expensive "Stuff"
Sho-Bud LDG
Desert Rose
Speedy West
Show Pro
Other Expensive "Stuff"
- Ken Metcalf
- Posts: 3575
- Joined: 21 Oct 2005 12:01 am
- Location: San Antonio Texas USA
- Contact:
So is it the consensus that 10s sound thinner but are more durable. As you increase the diameter of the string it becomes more prone to snapping and sounds fuller?
I haven't had any strings pop for years but lately I have been breaking my SIT 11s more.
I change the 3rd string every 3 or 4 gigs.
I haven't had any strings pop for years but lately I have been breaking my SIT 11s more.
I change the 3rd string every 3 or 4 gigs.
Last edited by Ken Metcalf on 5 Sep 2023 12:23 pm, edited 1 time in total.
-
- Posts: 217
- Joined: 15 Mar 2013 2:47 pm
- Location: Missouri, USA
I have a long-scale Excel (25½") and getting a .011" 3rd string up to pitch is a test of nerves, and strings!
As long as I stick to GHS which is the original fitment and if I take extreme care installing it, once on and working it lasts for ages. (Other brands obtainable in the UK snap before they get to G#, never mind the B pedal.) The Excel changer is very kind to strings and once fitted successfully the 3rd string eventually gets tired and tinny but doesn't break.
I am tempted to go for an easy life with a .0105 but I fear it would lack power.
As long as I stick to GHS which is the original fitment and if I take extreme care installing it, once on and working it lasts for ages. (Other brands obtainable in the UK snap before they get to G#, never mind the B pedal.) The Excel changer is very kind to strings and once fitted successfully the 3rd string eventually gets tired and tinny but doesn't break.
I am tempted to go for an easy life with a .0105 but I fear it would lack power.
Make sleeping dogs tell the truth!
Homebuilt keyless U12 7x5, Excel keyless U12 8x8, Williams keyless U12 7x8, Telonics rack and 15" cabs
Homebuilt keyless U12 7x5, Excel keyless U12 8x8, Williams keyless U12 7x8, Telonics rack and 15" cabs
- Tony Prior
- Posts: 14522
- Joined: 17 Oct 2001 12:01 am
- Location: Charlotte NC
- Contact:
always an interesting , valid, discussion. I keep the worlds supply of 11's on hand and have a few .0115's, (not 015's , thats a 15 ) I 've never used a 12.
11's have been reliable for any of the Steels I've owned and played thru the years, Emmons, Sho Buds, Carters etc...BUT- like a few here, when I was busy, I never went past 2 weeks before changing both 3 + 5. If I came off a 3 gig weekend, I changed both before the next week. I don't recall breaking a 3rd string on a gig for well over a decade, maybe longer when I was active, meaning playing gigs weekly.
Trial and error, see what works for you , there are no rules and also NO HOLY GRAIL 3rd string . Its the nature of the beast.
BEST
tp
11's have been reliable for any of the Steels I've owned and played thru the years, Emmons, Sho Buds, Carters etc...BUT- like a few here, when I was busy, I never went past 2 weeks before changing both 3 + 5. If I came off a 3 gig weekend, I changed both before the next week. I don't recall breaking a 3rd string on a gig for well over a decade, maybe longer when I was active, meaning playing gigs weekly.
Trial and error, see what works for you , there are no rules and also NO HOLY GRAIL 3rd string . Its the nature of the beast.
BEST
tp
Emmons L-II , Fender Telecasters, B-Benders
Pro Tools 8 and Pro Tools 12
jobless- but not homeless- now retired 8 years
CURRENT MUSIC TRACKS AT > https://tprior2241.wixsite.com/website
Pro Tools 8 and Pro Tools 12
jobless- but not homeless- now retired 8 years
CURRENT MUSIC TRACKS AT > https://tprior2241.wixsite.com/website