Skateboard Lap Steel

Lap steels, resonators, multi-neck consoles and acoustic steel guitars

Moderator: Brad Bechtel

Post Reply
Joe Engledow
Posts: 17
Joined: 2 May 2016 11:50 am
Location: California, USA

Skateboard Lap Steel

Post by Joe Engledow »

Hello to all my new friends!

I've joined the Steel Guitar Forum finally, after showing up at Larry Chung's inaugural Steel Guitar Summit with my humble "Franken-Skate" lap steel.

She came into my life as a broken skateboard deck from the manager at Skateworks in Los Altos. The cracks around the bolt holes only affected its rideability and they were parallel with the strings so I went with it.

I built this trying to keep the amount of "guitar parts" to a reasonable minimum. The tuning keys and ferrules came from C.B.Gitty. The P-90 pickups were sourced at The Gryphon stringed instruments. Almost everything else came from Lowe's hardware. The nut is simply an aluminum angle bracket. The bridge is 2 cable clamps suspending an aluminum turnbuckle.

The measurements were made with a plastic ruler and aren't accurate due to the curves of the material. The fret lines were burned in the wood haphazardly with my soldering tip.

Despite all this, it resonates beautifully and sounds good. Pitch bending and vibrato is accessible just by flexing the board. Scale length is 22.5 inches. It's wired in the Les Paul style.

At the moment it's tuned to Open A (E-A-E-A-C#-E) because it has electric guitar strings and not lap steel strings.

I welcome any and all discussion and questions. Pictures and video to follow in this thread.
Last edited by Joe Engledow on 5 May 2016 2:17 pm, edited 1 time in total.
Joe Engledow
Posts: 17
Joined: 2 May 2016 11:50 am
Location: California, USA

Post by Joe Engledow »

Image
Image
Image
Image
Joe Engledow
Posts: 17
Joined: 2 May 2016 11:50 am
Location: California, USA

Post by Joe Engledow »

Image
Image
Image
Joe Engledow
Posts: 17
Joined: 2 May 2016 11:50 am
Location: California, USA

Post by Joe Engledow »

The following two photos are by Alan Brookes and reposted from his photo thread on this forum.

Here is the event organizer, Larry Chung, tuning it up.
Image


This is my combo amplifier. Built by Xenrelic Amplification, it's a Champ-Amp circuit and a little 5 inch speaker, housed in a Wollensak tape recorder case.
Image

Here are more pictures of the amp hosted on Imgur.com.
User avatar
Charlie McDonald
Posts: 11054
Joined: 17 Feb 2005 1:01 am
Location: out of the blue

Post by Charlie McDonald »

I like it. Clever use of materials on the bridge and string trees.
Joe Engledow
Posts: 17
Joined: 2 May 2016 11:50 am
Location: California, USA

Post by Joe Engledow »

I took the skateboard lapsteel to Reno this weekend for an open mic performance.
Musicians and skaters came up to thank me. This is new territory for me.

Image

Image
Joe Engledow
Posts: 17
Joined: 2 May 2016 11:50 am
Location: California, USA

Second Steel Summit at the Gryphon

Post by Joe Engledow »

Photos by Alan F. Brookes


Image

Image

Image
Joe Engledow
Posts: 17
Joined: 2 May 2016 11:50 am
Location: California, USA

#Rocksmith5th

Post by Joe Engledow »

I also made a video on YouTube of my instrument, finally! It's the last third of this recording praising my guitar teaching tool, Rocksmith.

https://www.youtube.com/watch?v=a_W51BvfW6k
User avatar
Stu Schulman
Posts: 6526
Joined: 15 Oct 1998 12:01 am
Location: Ulster Park New Yawk (deceased)

Post by Stu Schulman »

Joe,How incredibly awesome!!!
Steeltronics Z-pickup,Desert Rose S-10 4+5,Desert Rose Keyless S-10 3+5... Mullen G2 S-10 3+5,Telonics 206 pickups,Telonics volume pedal.,Blanton SD -10,Emmons GS_10...Zirctone bar,Bill Groner Bar...any amp that isn't broken.Steel Seat.Com seats...Licking paint chips off of Chinese Toys since 1952.
Post Reply