Help, messed up my nuts!
Moderator: Shoshanah Marohn
- Cole Weidenbach
- Posts: 7
- Joined: 6 Dec 2022 1:16 am
- Location: Mississippi, USA
Help, messed up my nuts!
I mistakenly applied oil on my roller nuts, and it soaked into the "axle" assembly over time. Now my beloved 5th string roller is a tad loose and wobbly. At room playing volumes I hear it make a sound similar to not pressing the bar down enough... I'm thinking I should wipe it down without removing the assembly, restring/tune, and then apply Locktight. Do y'all think this is a good conservative first attempt or what would you do?
-
- Posts: 21192
- Joined: 16 Feb 1999 1:01 am
- Location: Glen Burnie, Md. U.S.A.
What do you mean the roller is “loose and wobbly”? Do you mean when there is a string on the roller pulled up to pitch? Or do you mean it’s like that when there is no string on the guitar? It’s common practice to oil the rollers, and no harm will ever come by it. In no case should Loctite be applied to anything but screw threads! If the hole is enlarged or “egged”, it indicates the guitar was not maintained properly, but read on…
Now, if you have a wobbly roller that's making noise, you can sometimes fix that by adding a drop of oil where the string contacts the roller. Or, with the string slacked, try rotating the roller a half-turn, and then retune the guitar and see if that helps. If the rollers are not gauged, you could also swap that roller with the one on the 9th or 10th string, as the heavier gauges are not as prone to rattle.
Ideally, you should replace the roller, or the entire roller nut assembly if the problem continues to be bothersome.
However, if the noise is not coming from the loose roller (and that is possible), you’ll have to resort to something else.
Now, if you have a wobbly roller that's making noise, you can sometimes fix that by adding a drop of oil where the string contacts the roller. Or, with the string slacked, try rotating the roller a half-turn, and then retune the guitar and see if that helps. If the rollers are not gauged, you could also swap that roller with the one on the 9th or 10th string, as the heavier gauges are not as prone to rattle.
Ideally, you should replace the roller, or the entire roller nut assembly if the problem continues to be bothersome.
However, if the noise is not coming from the loose roller (and that is possible), you’ll have to resort to something else.
- Cole Weidenbach
- Posts: 7
- Joined: 6 Dec 2022 1:16 am
- Location: Mississippi, USA
- Kelcey ONeil
- Posts: 327
- Joined: 1 May 2018 11:42 am
- Location: Sevierville, TN
- Contact:
Loctite is the last thing you want to use, it will no longer be a roller nut! Although it shouldn't rattle, being new really has nothing to do with it because it would take decades to wear them out, it may not fit well from the factory. Try winding your string at bit of an angle to put pressure on one side of the roller nut.
Co-owner and operator: Emmons Guitar Co.
-
- Posts: 21192
- Joined: 16 Feb 1999 1:01 am
- Location: Glen Burnie, Md. U.S.A.
In that case, I'd contact the manufacturer and request a new roller, which may or may not fix the problem if the gap for the roller in the nut support is simply too wide. Personally, I wouldn't advise making the string pull at an angle to eliminate the looseness, as that can cause increased hysteresis and tuning problems.Cole Weidenbach wrote:I don’t think it’s “egged” as the PSG is only 8 months old and the slack is mostly lateral. The movement is noticeable even when tensioned by the string and in tune.
I've never really seen this problem, personally, but I have noticed that some manufacturers use very skinny brass rollers, which would make the rollers less robust, causing this problem (worn or damaged rollers) to be far more likely to occur.
-
- Posts: 2235
- Joined: 17 May 2010 9:27 am
- Location: West Virginia, USA
What make is the guitar having this problem?
If the strings are old, Check where the 5th string rolls over the top of the changer finger, The string may have hardened and is raised up off the finger.
Mechanically it could be the 5th roller its self, Too narrow for the slot in the nut comb itself. Also check the slots, The 5 slot could be cut just a little wider and causing the problem.
Being a new guitar, The nut roller may have been assembled with some sort of stiff grease on the rollers, When you added oil, It thinned the grease and now the roller moves so easy, The roller may be viberating when the string is picked. Causing the sound.
Good Luck finding the problem and cure, Happy Steelin.
If the strings are old, Check where the 5th string rolls over the top of the changer finger, The string may have hardened and is raised up off the finger.
Mechanically it could be the 5th roller its self, Too narrow for the slot in the nut comb itself. Also check the slots, The 5 slot could be cut just a little wider and causing the problem.
Being a new guitar, The nut roller may have been assembled with some sort of stiff grease on the rollers, When you added oil, It thinned the grease and now the roller moves so easy, The roller may be viberating when the string is picked. Causing the sound.
Good Luck finding the problem and cure, Happy Steelin.
- Cole Weidenbach
- Posts: 7
- Joined: 6 Dec 2022 1:16 am
- Location: Mississippi, USA
It's a Stage One. Now that I recall, I bet I did wash out some stiff grease. Before applying rem oil, the rollers were firm and rolled with a nice "gritty" resistance feel. I'm going to try some grease I have and if that doesn't work I'm sure Doug can point me in the right direction. I'm glad I didn't move forward with the locktight, I can be impatient.
-
- Posts: 289
- Joined: 6 Sep 2021 10:45 pm
- Location: South Australia
-
- Posts: 1555
- Joined: 25 Feb 2011 2:47 pm
- Location: Arizona, USA
-
- Posts: 21192
- Joined: 16 Feb 1999 1:01 am
- Location: Glen Burnie, Md. U.S.A.