Hello!
I recently wound up with nice 1974 Pro 1 with the 1 up/1 down changer. It was originally a barrel behind two hole puller, but was modified with nylon endplate tuners, so some stops are tuned under the guitar, which doesn’t thrill me, but the guitar not only sounds amazing but it holds tune very well.
I have the proper ShoBud era parts to do a complete restoration plus add a knee lever or two. I’ve had several Buds in the past but never like this. I read the barrel behind puller system was a favorite among players, but now I’m get mixed reports from a few people regarding the tuning stability.
Needing help deciding whether to leave it as is or not. Welcoming any experiences or advice!
Thanks
Shobud barrels behind pullers
Moderator: Shoshanah Marohn
- Dave Zirbel
- Posts: 4170
- Joined: 4 Aug 1998 11:00 pm
- Location: Sebastopol, CA USA
Shobud barrels behind pullers
Dave Zirbel-
Sierra S-10 (Built by Ross Shafer),ZB, Fender 400 guitars, various tube and SS amps
Sierra S-10 (Built by Ross Shafer),ZB, Fender 400 guitars, various tube and SS amps
- Johnie King
- Posts: 8538
- Joined: 7 Apr 2014 11:09 am
- Location: Tennessee, USA
Dave Lloyd Greens 1973 Sho Bud was converted to nylon tuning set up years ago.
I built A pedal steel from Sho Bud parts that had brass barrels an I changed it too nylon tuning system..
Brass barrels are fine but I hesitate to sell a Sho Bud with Brass barrels too a customer that has little or no knowledge of how too properly use the brass barrels.
I built A pedal steel from Sho Bud parts that had brass barrels an I changed it too nylon tuning system..
Brass barrels are fine but I hesitate to sell a Sho Bud with Brass barrels too a customer that has little or no knowledge of how too properly use the brass barrels.
Last edited by Johnie King on 21 Sep 2023 6:43 pm, edited 1 time in total.
- Dave Zirbel
- Posts: 4170
- Joined: 4 Aug 1998 11:00 pm
- Location: Sebastopol, CA USA
Johnny, when Lloyd converted to nylon tuners did he also change to the double raise/single lower scissor finger?
The barrel system seems pretty straightforward to me. Same basic concept as the rack and barrel.
The barrel system seems pretty straightforward to me. Same basic concept as the rack and barrel.
Dave Zirbel-
Sierra S-10 (Built by Ross Shafer),ZB, Fender 400 guitars, various tube and SS amps
Sierra S-10 (Built by Ross Shafer),ZB, Fender 400 guitars, various tube and SS amps
- Jerry Jones
- Posts: 841
- Joined: 6 Sep 2007 4:26 pm
- Location: Franklin, Tenn.
Seems like I’ve been here before. Not quite a double raise but it does make adjustments easier.
Using a nylon nut type rod….for the C pedal use a standard 1/8” stop collar or a ShoBud barrel reversed. The A pedal uses a standard ShoBud brass barrel but with a knurled Tele knob installed at the end of rod.
Hold the Tele knob while engaging C pedal then tune with nylon nut.
Engage A pedal and turn Tele knob to adjust A pedal.
I used to have a bunch of these adapters for converting 1/4” shafts to 1/8”.
Using a nylon nut type rod….for the C pedal use a standard 1/8” stop collar or a ShoBud barrel reversed. The A pedal uses a standard ShoBud brass barrel but with a knurled Tele knob installed at the end of rod.
Hold the Tele knob while engaging C pedal then tune with nylon nut.
Engage A pedal and turn Tele knob to adjust A pedal.
I used to have a bunch of these adapters for converting 1/4” shafts to 1/8”.
Jerry Jones
- Dave Zirbel
- Posts: 4170
- Joined: 4 Aug 1998 11:00 pm
- Location: Sebastopol, CA USA
Thanks Jerry. That actually makes sense, I think that’s what the person was attempting to do.Using a nylon nut type rod….for the C pedal use a standard 1/8” stop collar or a ShoBud barrel reversed. The A pedal uses a standard ShoBud brass barrel but with a knurled Tele knob installed at the end of rod.
Hold the Tele knob while engaging C pedal then tune with nylon nut.
Engage A pedal and turn Tele knob to adjust A pedal.
Dave Zirbel-
Sierra S-10 (Built by Ross Shafer),ZB, Fender 400 guitars, various tube and SS amps
Sierra S-10 (Built by Ross Shafer),ZB, Fender 400 guitars, various tube and SS amps
- Kelcey ONeil
- Posts: 327
- Joined: 1 May 2018 11:42 am
- Location: Sevierville, TN
- Contact:
- Jason Putnam
- Posts: 546
- Joined: 18 Nov 2011 7:46 am
- Location: Tennessee, USA
Tips I remember from working on mine. 1. Screw the barrel to the half way point and then slide it next to the puller and tighten the set screw. That gives the most in or out adjustment for tuning. 2. Make sure the spring tip is protruding from the little hole in the barrel. This is what catches on the puller and causes it to screw in and out while tuning. 3. Make sure the threads are dry and that no oil is placed on them. They should have resistance otherwise if oiled, they will screw or unscrew while your playing causing tuning issues.
1967 Emmons Bolt On, 1974 ShoBud Pro 1 3x5,Nashville 112, Quilter TT-12, JOYO Digital Delay, Goodrich Volume Pedal, Livesteel Strings
- Ian Worley
- Posts: 2119
- Joined: 14 Jan 2012 12:02 pm
- Location: Sacramento, CA
The barrels only provide a tangible benefit on rods with two or more pedal/lever changes. The barrels are more prone to slip/spin and drift out of tune while playing than nylon too. You can keep the clamping set-screw swivels and nylon tuners on all the other rods with only one raise or one lower. Instead of the original style socket head rods, just epoxy the nuts onto the rods that use the barrels so you'll only need the one wrench to tune
All lies and jest, still a man hears what he wants to hear and disregards the rest - Paul Simon