curly maple??

Jimmie Martin · Post by **Jimmie Martin** » 21 Apr 2005 1:00 pm

i need to buy some curly maple and i tried 2 places on the internet and they wanted a lot of money for it. like 2 hundred dollars for 3 pieces of 3/4" by 12" by 36". there has to be somewhere it can be bought cheaper. thanks guys

Farris Currie · Post by **Farris Currie** » 21 Apr 2005 1:13 pm

Robert,i bought birdseye, and myrtle wood from TimberLand but it sure isn't cheap.and the shipping will kill ya to.i got 8ft.boards shipped ups.almost as much as the wood cost.good luck farris

Mark Vinbury · Post by **Mark Vinbury** » 21 Apr 2005 3:09 pm

Try eBay.There is a lot of great wood available for reasonable prices.

Webb Kline · Post by **Webb Kline** » 21 Apr 2005 6:04 pm

Robert, Call Dwight Lewis Lumber Co. in Picture Rocks, PA. Mel and Mark are about as reasonable as anyone I've ever delt with. You can probably get what you're looking for for under 50 bucks delivered.

It's all good Northern Tier Maple too. That's about as good as it gets.

1 800 233 8450.

Jimmie Martin · Post by **Jimmie Martin** » 21 Apr 2005 6:12 pm

thanks guys. i will give those guys a call.

Steve Frost · Post by **Steve Frost** » 21 Apr 2005 6:30 pm

The 12 inch width you mention you mention may be the culprit. Around here, curly maple is about $6 a board foot, but I don't see much that's 12 inches wide with good figure. Good luck!

Al Carmichael · Post by **Al Carmichael** » 22 Apr 2005 7:53 am

Have you checked any hardwood lumber mills in your area? I buy this sort of thing locally. It still ain't cheap, but if you can see what you are buying and you can cut out the shipping cost, you'll be way ahead.

Mark Ardito · Post by **Mark Ardito** » 22 Apr 2005 8:38 am

Robert,

Curly Maple is not that "rare" and should be available at ANY local lumber mill or hard wood dealer in Ohio. However, you will be HARD pressed to find a piece of Curly Maple with high figure that is 12" wide. You will be looking at a "glue up" for this width. Find yourself a hard wood dealer in the Yellow Pages and that should do it. If you don't have the proper tools to make the glue-up, most lumber mills or dealers will do it for you at an additional fee...just a few bucks.

Cheers!
Mark Ardito

------------------
Sho~Bud Pro I, Fender D-8 (C6&E13) http://www.darkmagneto.com
http://www.arditotech.com

Ron ! · Post by **Ron !** » 22 Apr 2005 8:42 am

I recently bought some birdseye here in the Netherlands.Over here birdseye is twice as much as in America.The 4 pieces I bought are just enough to build me a Double body cabinet.Price.....€342euro.
It's just that this will be my personal steel and there for I am using massive Birdseye.Normally I use birdseye finish.Don't cost that much.

Ron

------------------
Nikaro Steel Guitars
Nikaro SD10 4x6-Nikaro SD10 4x5-2Peavey 112 Ultra Tube.
 nikarosteelguitars@planet.nl 
European Steel Guitar Forum

Jimmie Martin · Post by **Jimmie Martin** » 2 May 2005 3:15 am

you can close this topic

Jennings Ward · Post by **Jennings Ward** » 12 May 2005 6:40 pm

ROBERT, I HAD THE SSAME PROBLEM AS YOU..TO MANNY DOLLARS AND NOT ENOUGH WOOD. I WANTED TO BUILD FIDDLES AND MANDOLINS ECT: WELL AFTER RUNNING UP BLIND ALLEYS FOR TOO LONG, I WENT TO,,,,,,,,,GEORGIA PACIFIC...... IN BLUEFIELD W.VA. THEY BUY UP ALL THE TIMBER ARROUND THERE......THEY SOLD ME A CURLY MAPLE TREE, CUT IT IN LENGTHS THAT I COULD HANDLE, 36 INCHES AND I BRAUGHT THE WHOLE TREE HOME.... THIS WAS ABOUT 5 YRS AGO AND IT COST ME $ 70.00 FOR A WHOLE TREE, {LOG } WITH ABOUT 100 BOARD FEET OF LUMBER..... BLUEFIELD IS NOT TOO FAR FROM YOU, IF YOU ARE IN A HYRRY.....12 " CURLY MAPLE 6 QUARTER,, FORGET IT..... ANY AND ALL CURLEY MAPLE THEY GET IS MADE INTO VINEER....THAT IS THE REASON THAT THE PRICE IS SO HIGH, OR ONE OF THEM.....GOOD LUCK IN YOUR QUEST FOR C.M. JENNINGS

------------------
EMMONS D10 10-10 profex 2 deltafex ne1000 pv1000, pv 31 bd eq, +