Page 1 of 1
Clamp to the leg multi effects processor?
Posted: 1 Nov 2023 8:02 am
by Larry Dering
Anyone using a small multi effects processor that's attached to the rear leg? At one time the Line 6 Pod XT was popular,(I still use one). Most of the stuff has been rack mounted, but that too has fizzled out in popularity. I haven't seen much else available. What do you use?
Posted: 3 Nov 2023 8:43 am
by Ken Metcalf
Pedal Train with hard case.
Posted: 3 Nov 2023 1:16 pm
by Larry Dering
That's a good setup but a bit large. I'm thinking along the lines of Nux amp academy, or Boss IR 200 amp and cab simulator. I want it on a bracket and mounted to the back leg.
Leg mount effects setup
Posted: 5 Nov 2023 6:20 am
by Ray DeVoe
Hi Larry.
Here is something I made up quick if I just want to use the typical dual effect pedal.
I had a non-used Peterson Tuner mount sitting around and that's what I used for the fastening system. I wanted to keep everything thin and light, so I cut a rectangle out of a clip board made from hard material. I used the threaded hole in the mount and fastened the cut piece to it. Once everything was fastened well where it would not turn, I used Velcro to fasten the pedal. Its simple but it works. This may not be what you are looking for but it makes for a quick shelf if you want to keep it quick and easy.
Ray D.
Posted: 5 Nov 2023 2:08 pm
by Larry Dering
Ray, I like it. I'm hoping some players will chime in and talk about they stuff they use like what you have. The Zoom MS50 was popular and so was the Line 6 Pods. With all the newest amp modeling stuff now I expected a lot of ideas to come forward. Thanks Ray
Ms-50
Posted: 5 Nov 2023 7:44 pm
by Gil James
If it ain't broke, dont fix it.
Pretty much just use the delay and reverb on it,but it's what I still use for grab and go gigs.
Posted: 6 Nov 2023 5:26 am
by Roger Crawford
Posted: 6 Nov 2023 7:34 am
by Larry Dering
Gil and Roger, thanks. I do like the seat bracket Roger has and I may use that method. So many of the processors are large and the seat bracket takes the load a little better.
Rack
Posted: 8 Nov 2023 5:40 pm
by Larry Allen
Posted: 8 Nov 2023 7:54 pm
by Larry Dering
Larry, yep that works. I just got the Nux Amp academy and played about an hour. The clean amps with it's built in reverb was very good. I didn't tweak any settings except reverb. Very positive impression. I ran it into my Quilter 202 to a TT 12 in separate cabinet. I used the effects return input on the Quilter.
Posted: 10 Nov 2023 8:15 am
by David Wren
Years ago I bought a Line 6 HX Stomp, multi FX unit, and also a 2 button switch that toggles through my presets.
The switch is small, and I have it mounted on my rear right leg. I don't have to touch the HK Stomp pedal at all... works great for switching presets in the middle of a song.
Here's a forum link with pix.
https://bb.steelguitarforum.com/viewtop ... highlight=
The unit is capable of tons of presets... I use 5
Posted: 10 Nov 2023 8:29 pm
by Larry Dering
David thanks. I was considering the HX stomp. Good quality effects and amp models in that little box.
Posted: 13 Nov 2023 10:52 pm
by Jim Cohen
Here's my new little effects rig. It's actually a Donner pedal rack mounted upside down to an adjustable iPad/tablet holder, clamped to the back leg of the steel. So far so good. First field test this Saturday night.
Posted: 14 Nov 2023 3:52 am
by Larry Dering
Jim, are you going through an amp or using the amp simulation from the Zoom into the mixer? I know the Zoom MS50G has some popularity here. That Multistomp is mainly an effects pedal but I read you can use software to add amps and effects.
Posted: 14 Nov 2023 7:19 am
by Ron Hogan
Drum hardware and then I tapped threads into the side of the effect, added
Loctite.
Posted: 14 Nov 2023 7:24 am
by Jim Cohen
Larry Dering wrote:Jim, are you going through an amp or using the amp simulation from the Zoom into the mixer?
So far I'm only using this for driving dates when I bring an amp. I haven't really thought yet about whether I want to use it for fly dates when I go through the Dream pedal.
Posted: 15 Nov 2023 8:22 am
by Larry Dering
Thanks Jim.
Ron, how satisfied are you using the Zoom products?