Bridge/Nut String Spacing and Intonation
Moderator: J D Sauser
-
- Posts: 20
- Joined: 23 Oct 2006 12:01 am
- Location: Honomu, Big Island, Hawai'i
Bridge/Nut String Spacing and Intonation
Aloha Builders,
I am in the middle of a build and have a question about string spacing. I see that it is very common to have a wider spacing at the bridge and narrower at the nut. My question is, wouldn't this create longer strings at the outside and narrower at the middle? Wouldn't that in turn create an out of tune chord when pressing down the bar and playing across the strings? Or maybe there is some compensation in the height of the strings in the bridge/nut or some other magic I am unaware of. Or maybe miraculously this doesn't really matter to the ears (although I bet it would to some). Admittedly I have not done extensive research on this, but after 30 mins of searching I haven't found an answer and hence this post.
Mahalo for your kokua!!
I am in the middle of a build and have a question about string spacing. I see that it is very common to have a wider spacing at the bridge and narrower at the nut. My question is, wouldn't this create longer strings at the outside and narrower at the middle? Wouldn't that in turn create an out of tune chord when pressing down the bar and playing across the strings? Or maybe there is some compensation in the height of the strings in the bridge/nut or some other magic I am unaware of. Or maybe miraculously this doesn't really matter to the ears (although I bet it would to some). Admittedly I have not done extensive research on this, but after 30 mins of searching I haven't found an answer and hence this post.
Mahalo for your kokua!!
- Andy DePaule
- Posts: 2576
- Joined: 20 Jun 1999 12:01 am
- Location: Saigon, Viet Nam & Springfield, Oregon
- Contact:
Yes but...
Hi Christian,
Yes but it so little extra width that it makes no difference. Remember we are not glued to the frets like a standard guitar and they have the same issue.
When we play steel the frets are just places to aim for with our eyes and our ears tell us when we are there. Even if the frets are not in the perfect place we'd still play much the same.
Some steels have less width difference between the nut and bridge and others have almost parallel strings. Parallel strings are not for that reason, but to make bar slants easier in the lower fret positions.
More important is string length. Longer scales 24&1/2" to 25&1/4" make harmonics easier to get. The shorter scales around 22.5" make bar slants easier.
For pedal steels 24" to 24&1/4" are kind of a standard with a few exceptions, but that is to help prevent string breakage with all the string stretching from the pedals and knee levers.
I prefer the shorter scales length because I'm not very good with harmonics anyway and do better with slants. There is no hard rule because it's just a matter of the players preference.
Good luck with the build,
Andy
Yes but it so little extra width that it makes no difference. Remember we are not glued to the frets like a standard guitar and they have the same issue.
When we play steel the frets are just places to aim for with our eyes and our ears tell us when we are there. Even if the frets are not in the perfect place we'd still play much the same.
Some steels have less width difference between the nut and bridge and others have almost parallel strings. Parallel strings are not for that reason, but to make bar slants easier in the lower fret positions.
More important is string length. Longer scales 24&1/2" to 25&1/4" make harmonics easier to get. The shorter scales around 22.5" make bar slants easier.
For pedal steels 24" to 24&1/4" are kind of a standard with a few exceptions, but that is to help prevent string breakage with all the string stretching from the pedals and knee levers.
I prefer the shorter scales length because I'm not very good with harmonics anyway and do better with slants. There is no hard rule because it's just a matter of the players preference.
Good luck with the build,
Andy
Inlaid Star Guitar 2006 by Mark Giles. SD-10 4+5 in E9th; http://luthiersupply.com/instrument-gallery.html
2017 Mullen SD-10, G2 5&5 Polished Aluminum covering. Custom Build for me. Great Steel.
Clinesmith Joaquin Murphy style Aluminum 8 String Lap Steel Short A6th.
Magnatone Jeweltone Series Lap Steel, Circa 1950? 6 String with F#minor7th Tuning.
1956 Dewey Kendrick D-8 4&3, Restoration Project.
1973 Sho~Bud Green SD-10 4&5 PSG, Restoration Project.
2017 Mullen SD-10, G2 5&5 Polished Aluminum covering. Custom Build for me. Great Steel.
Clinesmith Joaquin Murphy style Aluminum 8 String Lap Steel Short A6th.
Magnatone Jeweltone Series Lap Steel, Circa 1950? 6 String with F#minor7th Tuning.
1956 Dewey Kendrick D-8 4&3, Restoration Project.
1973 Sho~Bud Green SD-10 4&5 PSG, Restoration Project.
-
- Posts: 20
- Joined: 23 Oct 2006 12:01 am
- Location: Honomu, Big Island, Hawai'i
Thanks Andy
Thanks Andy, I suspected as much. Just making sure I am not making some grievous error as I am a builder newbie. Mahalo sir!
- Ian Worley
- Posts: 2119
- Joined: 14 Jan 2012 12:02 pm
- Location: Sacramento, CA
As Andy said, the difference in scale length is much to small to be of concern. On a typical 24" scale 10 string guitar w/ ~11/32" string spacing at the bridge and ~19/64" at the nut, the difference in scale length between the two shortest inner strings and the two longest outer strings is less than 1/1000". 24.00000824 - 24.00066734 = 0.0006591".
That would amount to ~0.06 cents tuning difference at the 7th fret, but more important to note that the ratios between frets, nut and bridge remain constant regardless of the relative angle of the string. On a steel guitar with fixed parallel bridge and nut, each string has a very slightly different scale length, but ratios for a bar placed above a given fret and parallel to the bridge/nut/frets are constant.
That would amount to ~0.06 cents tuning difference at the 7th fret, but more important to note that the ratios between frets, nut and bridge remain constant regardless of the relative angle of the string. On a steel guitar with fixed parallel bridge and nut, each string has a very slightly different scale length, but ratios for a bar placed above a given fret and parallel to the bridge/nut/frets are constant.
All lies and jest, still a man hears what he wants to hear and disregards the rest - Paul Simon
Ian is right - the geometry of similar triangles takes care of the tuning.
As far as I can see, the only reason for tapering towards the nut is aesthetic, but it's a nice aesthetic - I did it when I built mine
As far as I can see, the only reason for tapering towards the nut is aesthetic, but it's a nice aesthetic - I did it when I built mine
Make sleeping dogs tell the truth!
Homebuilt keyless U12 7x5, Excel keyless U12 8x8, Williams keyless U12 7x8, Telonics rack and 15" cabs
Homebuilt keyless U12 7x5, Excel keyless U12 8x8, Williams keyless U12 7x8, Telonics rack and 15" cabs
- Dave Mudgett
- Moderator
- Posts: 9648
- Joined: 16 Jul 2004 12:01 am
- Location: Central Pennsylvania and Gallatin, Tennessee
I agree with everything stated - the differences in scale length are too small to hear, the similar triangle argument stating that the ratio of string length in front and behind the bar doesn't change is correct, not to mention the fact that bar placement overrides every other single issue except perhaps serious errors in open string tuning.
And add to that the fact that the model on which all these string tension vs. scale length vs. pitch calculations are made uses a very idealized model of a string which is not realized in practice. One issue is that strings have stiffness which varies from string to string. So there is a distance from the takeoff point at the nut and bridge where vibration is not free, which reduces the effective scale length of the string, and that varies from string to string. This is part (but not all) of what causes fretted guitars to need variable lengths of compensation for different strings. With fretted guitar, there is also the vertical string deflection caused by fretting the string. And no doubt other second and/or third-order effects.
If one was to worry about this stuff, one would go nuts trying to play. Playing in tune must be handled by hand/eye/ear coordination and an experiential understanding of where there may be slight tuning issues on the guitar. That is my belief, anyway.
And add to that the fact that the model on which all these string tension vs. scale length vs. pitch calculations are made uses a very idealized model of a string which is not realized in practice. One issue is that strings have stiffness which varies from string to string. So there is a distance from the takeoff point at the nut and bridge where vibration is not free, which reduces the effective scale length of the string, and that varies from string to string. This is part (but not all) of what causes fretted guitars to need variable lengths of compensation for different strings. With fretted guitar, there is also the vertical string deflection caused by fretting the string. And no doubt other second and/or third-order effects.
If one was to worry about this stuff, one would go nuts trying to play. Playing in tune must be handled by hand/eye/ear coordination and an experiential understanding of where there may be slight tuning issues on the guitar. That is my belief, anyway.
-
- Posts: 376
- Joined: 9 Jul 2019 7:33 am
- Location: New South Wales, Australia
It's basically a remnant of the origins of Steel guitar coming from the Spanish (fretted) guitar where left hand comfort and ergonomics were better with a narrower nut, but the plucking hand was better with a wider string spacing.
A taper just tends to look right to the eye when we are used to seeing it.
Makes NO difference to intonation.
My Duesenberg has equal spacing
A taper just tends to look right to the eye when we are used to seeing it.
Makes NO difference to intonation.
My Duesenberg has equal spacing
Duesenberg Fairytale
1949 Supro Supreme
1950 National New Yorker
2008 Highland Baritone Weissenborn
2020 Highland New Yorker.
2020 Highland Mohan Veena
2021 Highland Weissencone
1949 Supro Supreme
1950 National New Yorker
2008 Highland Baritone Weissenborn
2020 Highland New Yorker.
2020 Highland Mohan Veena
2021 Highland Weissencone
String Angle and Spacing
Here is a related discussion with Paul Franklin and Buddy Emmons where Buddy comes up with some interesting ideas about angles and spacing as well as some fascinating history of the instrument.
https://bb.steelguitarforum.com/viewtop ... highlight=
https://bb.steelguitarforum.com/viewtop ... highlight=
- Andy DePaule
- Posts: 2576
- Joined: 20 Jun 1999 12:01 am
- Location: Saigon, Viet Nam & Springfield, Oregon
- Contact:
I flunked out
Hay you guys are making me feel bad. I flunked out of geometry and algebra was another story, with that it was not the answer that was hard for me, it was what the question was!
I'm not kidding, Been building guitars since 1969 and use geometry to get that done all the time, but I have no idea how to do the math involved.
It was always my worst subject. I did good in art & shop class.
I also always liked history because I'm a dreamer and could imagine myself in those times and places.
I'm not kidding, Been building guitars since 1969 and use geometry to get that done all the time, but I have no idea how to do the math involved.
It was always my worst subject. I did good in art & shop class.
I also always liked history because I'm a dreamer and could imagine myself in those times and places.
Inlaid Star Guitar 2006 by Mark Giles. SD-10 4+5 in E9th; http://luthiersupply.com/instrument-gallery.html
2017 Mullen SD-10, G2 5&5 Polished Aluminum covering. Custom Build for me. Great Steel.
Clinesmith Joaquin Murphy style Aluminum 8 String Lap Steel Short A6th.
Magnatone Jeweltone Series Lap Steel, Circa 1950? 6 String with F#minor7th Tuning.
1956 Dewey Kendrick D-8 4&3, Restoration Project.
1973 Sho~Bud Green SD-10 4&5 PSG, Restoration Project.
2017 Mullen SD-10, G2 5&5 Polished Aluminum covering. Custom Build for me. Great Steel.
Clinesmith Joaquin Murphy style Aluminum 8 String Lap Steel Short A6th.
Magnatone Jeweltone Series Lap Steel, Circa 1950? 6 String with F#minor7th Tuning.
1956 Dewey Kendrick D-8 4&3, Restoration Project.
1973 Sho~Bud Green SD-10 4&5 PSG, Restoration Project.
- Andy DePaule
- Posts: 2576
- Joined: 20 Jun 1999 12:01 am
- Location: Saigon, Viet Nam & Springfield, Oregon
- Contact:
Doubt I'd be better off
Hi Ian,
Doubt I'd be better off if I could do those things.
Been self employed most of my life and as long as I can add, subtract, multiply and divide that's all I've ever really needed.
More important is that I can ball park those 4 in my head and usually get close enough.
My worst sin is that as much as I the actually hate doing math is that I alway put it off too long and then have to spend days catching up for taxes.
This year I've been doing month end totals with YTD so maybe I can get it down to a few hours at the end of this year.
Doubt I'd be better off if I could do those things.
Been self employed most of my life and as long as I can add, subtract, multiply and divide that's all I've ever really needed.
More important is that I can ball park those 4 in my head and usually get close enough.
My worst sin is that as much as I the actually hate doing math is that I alway put it off too long and then have to spend days catching up for taxes.
This year I've been doing month end totals with YTD so maybe I can get it down to a few hours at the end of this year.
Inlaid Star Guitar 2006 by Mark Giles. SD-10 4+5 in E9th; http://luthiersupply.com/instrument-gallery.html
2017 Mullen SD-10, G2 5&5 Polished Aluminum covering. Custom Build for me. Great Steel.
Clinesmith Joaquin Murphy style Aluminum 8 String Lap Steel Short A6th.
Magnatone Jeweltone Series Lap Steel, Circa 1950? 6 String with F#minor7th Tuning.
1956 Dewey Kendrick D-8 4&3, Restoration Project.
1973 Sho~Bud Green SD-10 4&5 PSG, Restoration Project.
2017 Mullen SD-10, G2 5&5 Polished Aluminum covering. Custom Build for me. Great Steel.
Clinesmith Joaquin Murphy style Aluminum 8 String Lap Steel Short A6th.
Magnatone Jeweltone Series Lap Steel, Circa 1950? 6 String with F#minor7th Tuning.
1956 Dewey Kendrick D-8 4&3, Restoration Project.
1973 Sho~Bud Green SD-10 4&5 PSG, Restoration Project.
-
- Posts: 1901
- Joined: 29 Aug 1998 12:01 am
- Location: Waterbury Ctr. VT 05677 USA