BMI and BSG Steels
Moderator: Shoshanah Marohn
-
- Posts: 1034
- Joined: 3 Apr 2006 12:01 am
- Location: Hardin, Kentucky, USA
BMI and BSG Steels
Does anyone have in experience with or own either of these guitars? I hear and read many comments on Sho-Buds, Fesseys, Rains, Emmons, etc., but I have never read any reviews on the BMI or the BSGs. I am considering getting a S-10 and I would appreciate any comments you may have on these two brands.
Thanks in advance.
Wally Taylor
Thanks in advance.
Wally Taylor
-
- Posts: 7252
- Joined: 6 Nov 1998 1:01 am
- Location: Atlanta Ga. USA
The BMI has a track record going all the way back to Zane Beck. Can't get a better start. Nice instrument that sounds great and continues to be built the way it was when the Beck company designed it. There is something to the Beck changer the way it hooks into the back casting and pulls into the guitar. I think it transfers a lot of tone and sustaing rather than having the changer axle suspended in the air between two posts. Good sounding and simple.
I have also seen the BSG guitar. Nicely made. Did not get to hear it. Check out both of the websites of these makers.
I have also seen the BSG guitar. Nicely made. Did not get to hear it. Check out both of the websites of these makers.
-
- Posts: 1944
- Joined: 27 Oct 2002 12:01 am
- Location: Gahanna, Ohio, USA
-
- Posts: 1153
- Joined: 3 Apr 2006 12:01 am
- Location: Illinois, USA
Ditto!! Bil and Pat. The earlier style BMI's with neck rails actually screwing into the side of the changer block are less prone to detuning than the present-day "C-shaped" tuner extrusion. I have a 1978 D11 with the long rails and a 1979 S10 with the short ones. Years ago I machined off the ears from the extrusion, made new 3/8" rails (the stock ones were 1/4"), and screwed them to the changer a la earlier models. When I don't need my Univ12, I play the S10 all the time. The prying action you described is different than what most scissors changers do today. It seems to be very repetitive and I have very seldom tweaked a nylon tuner on either one of these guitars since I've owned them. I shortened the S10 by 4.000" last year and built a keyless tuner for it. Had I not wanted to retain the 1st pedal where it was, I could have taken off another 1.500". I did some additional work on the underside. . .ledges for the face board to nest on with additional screws, etc. This wasn't necessary, merely something I wanted to do to tie the basic cabinet together tighter. A fine little (and I do mean little) guitar.
PRR
PRR
I've had a BSG since Feb. 04 and haven't broken a string yet. It stays in tune and has great action and tone. Builder Don Burrows machines all parts and is sure all parts fit and operate properly. He takes great pride in his work. Check out his website at www.bsgsteelguitars.com
Feel free to email Don, he can answer any questions you may have.
------------------
Wayne Hetzler
04 BSG SD10
98 Carter SD10
Feel free to email Don, he can answer any questions you may have.
------------------
Wayne Hetzler
04 BSG SD10
98 Carter SD10
-
- Posts: 829
- Joined: 16 Aug 2005 12:01 am
- Location: Ramsey Illinois, USA Hometown of Tex Williams
- Mike Sigler
- Posts: 1479
- Joined: 4 Feb 1999 1:01 am
- Location: Give Em A Try !
- Contact:
-
- Posts: 21192
- Joined: 16 Feb 1999 1:01 am
- Location: Glen Burnie, Md. U.S.A.
-
- Posts: 1034
- Joined: 3 Apr 2006 12:01 am
- Location: Hardin, Kentucky, USA
Hey, thanks guys for all the replys about the BMI and BSG guitars. I had visited the sites of both many times, but there is nothing like first hand experience and you can't get better experience than guys on the forum. I admire and greatly respect everyone's views. Your input will all be considered towards my next purchase of a steel guitar,
Again, many thanks,
Wally Taylor
Again, many thanks,
Wally Taylor