The Steel Guitar Forum Store 

Post new topic Recommended Steel King set up for E9th and C6th
Reply to topic
Author Topic:  Recommended Steel King set up for E9th and C6th
Jeshua Lehman

 

From:
Ivor, VA
Post  Posted 13 Oct 2010 7:12 am    
Reply with quote

I bought a Steel King amp yesterday and it is in the mail to me. The amp was used and doesn't have a user manual. I am looking for the setup that ya'll use so when I get it I can start playing around with variation that other like. I bet this is already been discussed so if you find a link to it that would be helpful, but I looked and was unsuccessful.
_________________
pre-RP Mullen D-12, Fender Steel King
View user's profile Send private message Send e-mail

Michael Robertson


From:
Ventura, California. USA
Post  Posted 13 Oct 2010 8:06 am     Steel king EQ.
Reply with quote

A lot depends on your guitar and how you want it to sound of course.
Keep in mind for a clean setting the Master Volume level should be open more than the Gain control.
The EQ circuit is post/after the Gain setting and at times it can be a balancing act between EQ response and volume at which you want to perform.
For starters have the tone controls down the middle dead flat.
With the Mid Control I dump mine to the left at roughly the ten o’clock position.
Then with the Frequency I sweep to the right and somewhere around 800 you find that the mid frequency bump will fall off.
That alone should get you real close.
During a gig I have found that the EQ Tilt control provides a good and quick fix tool for the particular tonal response of the venue.
Good luck and have fun with your Steel King. I love mine……….. Until I have to lift it.
Michael
View user's profile Send private message Send e-mail

Bob Lawrence


From:
Beaver Bank, Nova Scotia, Canada
Post  Posted 13 Oct 2010 6:39 pm    
Reply with quote

You can download a copy of the manual with this Link

http://support.fender.com/manuals/manuals_elec/guitarpdf//Steel_King.pdf
View user's profile Send private message Send e-mail

Mike Kowalik

 

From:
San Antonio,Texas
Post  Posted 14 Oct 2010 4:51 am     Steel King settings....
Reply with quote

Here's mine....EQ Tilt 12 o'clock, Treble 11 o'clock, Mid Level 10 o'clock, Mid Freq 2 o'clock, Bass between 3 and 5 o'clock. Normal and Limiter buttons out.

This is with a push pull that has stock single coil pick-ups.
I never cared for the sound of my Steel King with the Fender speaker...so I replaced it with a BW 1502-4 and a 1501-4...what a difference.

Also had Rick Johnson build seperate cabinets for the head and speaker to make transport easier.
_________________
Cremation is my last shot at having a hot body......
View user's profile Send private message Send e-mail

Jeshua Lehman

 

From:
Ivor, VA
Post  Posted 16 Oct 2010 5:50 am    
Reply with quote

I just received my steel king and can't wait to start playing, but I have to wait until my lazy roommate wakes up. Thanks for all your suggestions.
_________________
pre-RP Mullen D-12, Fender Steel King
View user's profile Send private message Send e-mail

Mike Kowalik

 

From:
San Antonio,Texas
Post  Posted 16 Oct 2010 7:27 am    
Reply with quote

Turn the gain on your Steel King to 10 and wake him up!!!!!!!!!
_________________
Cremation is my last shot at having a hot body......
View user's profile Send private message Send e-mail

Michael Robertson


From:
Ventura, California. USA
Post  Posted 16 Oct 2010 7:30 am    
Reply with quote

Mike Kowalik wrote:
Turn the gain on your Steel King to 10 and wake him up!!!!!!!!!

10 is good. Very Happy Laughing Very Happy Laughing
View user's profile Send private message Send e-mail


All times are GMT - 8 Hours
Jump to:  

Our Online Catalog
Strings, CDs, instruction,
steel guitars & accessories

www.SteelGuitarShopper.com

Please review our Forum Rules and Policies

Steel Guitar Forum LLC
PO Box 237
Mount Horeb, WI 53572 USA


Click Here to Send a Donation

Email admin@steelguitarforum.com for technical support.


BIAB Styles
Ray Price Shuffles for
Band-in-a-Box

by Jim Baron
HTTP