GFI Players,..Come on in (II) (*Updated 10/30/10)
Posted: 27 Apr 2010 12:44 pm
That other ol' GFI thread (of mine) was getting a little bit 'long in the tooth', so I elected to start up another one, for the sake of our mutual convenience. Well..that, and so these new updates won't wind up getting buried at the bottom of page four of the old one.
If you're a GFI player, and looking for info on the Nylon mods, VKL kit, or any of several other oddities of mine, I'll refer you to page #1 of the old thread,as opposed to repeating all that stuff in here.
All that stuff is still right here > http://bb.steelguitarforum.com/viewtopi ... highlight=[/b]
Today, however, I've got a special, limited offer for three S-10, or SD-10 GFI'ers.
I've been experimenting with some new finishes on the Slyde-Car's
These are all applique finishes:
On the left, is a chrome, which is kinda wet looking or, like a rear-view mirror that's a little iced over, in this picture.
On the top, is a prismatic decal material that really catches the light.
On the right, is what is called a 'carbon fiber' finish. I think it sorta has the look of an older type, flat braided battery cable.
Here are some other views of all three.
Chrome > Picture file
Prismatic (Indoor)> Picture file
Braided > Picture file
I've got these three units, ready to go and pre-fitted for a double framed GFI guitar.
These will go to first three GFI'ers that want em'. I consider these experimental, or demo units so they're discounted to $30 ea, + S&H ($5 0ff)
(Update)
*I neglected to mention that these 3 units are standard sized trays, for a 7/8 bar.
Some of you may be wondering what I did to my guitar....
A little Face-lift......Going from
This.. > ...To this >
She used to look like this:
Now...this is much more to my liking; simulating the traditional end-plate 'look', and a little added 'glitz'.
More mid sized pix > Picture file
Picture file
Picture file
Picture file
Picture file
Picture file
Picture file
Picture file
Picture file
Alrighty then,...enough of that.
There are probably a few newer GFI players nowadays, since that first thread.
I'd like to briefly address those players; whom, up until now, have been fortunate enough to remain unaware of my existence.
If anyone is interested in the DIY Nylon washer mod, I still have a few 'kits' left.
Simply send a self-addressed, pre-stamped envelope, along with $3 per neck to:
Dale Hansen
(Bessdang Gizmos)
2661 Long Hollow Pike
Hendersonville, Tn
37075-8721
It might be a good idea to drop me a line, so I know to watch for it in the mail.
Also, as of this week, there are 3 new videos about all of this stuff.
Click on my > WWW dot 'thing-a-ma-b0b' below, and it will take you right there.
If you're a GFI player, and looking for info on the Nylon mods, VKL kit, or any of several other oddities of mine, I'll refer you to page #1 of the old thread,as opposed to repeating all that stuff in here.
All that stuff is still right here > http://bb.steelguitarforum.com/viewtopi ... highlight=[/b]
Today, however, I've got a special, limited offer for three S-10, or SD-10 GFI'ers.
I've been experimenting with some new finishes on the Slyde-Car's
These are all applique finishes:
On the left, is a chrome, which is kinda wet looking or, like a rear-view mirror that's a little iced over, in this picture.
On the top, is a prismatic decal material that really catches the light.
On the right, is what is called a 'carbon fiber' finish. I think it sorta has the look of an older type, flat braided battery cable.
Here are some other views of all three.
Chrome > Picture file
Prismatic (Indoor)> Picture file
Braided > Picture file
I've got these three units, ready to go and pre-fitted for a double framed GFI guitar.
These will go to first three GFI'ers that want em'. I consider these experimental, or demo units so they're discounted to $30 ea, + S&H ($5 0ff)
(Update)
*I neglected to mention that these 3 units are standard sized trays, for a 7/8 bar.
Some of you may be wondering what I did to my guitar....
A little Face-lift......Going from
This.. > ...To this >
She used to look like this:
Now...this is much more to my liking; simulating the traditional end-plate 'look', and a little added 'glitz'.
More mid sized pix > Picture file
Picture file
Picture file
Picture file
Picture file
Picture file
Picture file
Picture file
Picture file
Alrighty then,...enough of that.
There are probably a few newer GFI players nowadays, since that first thread.
I'd like to briefly address those players; whom, up until now, have been fortunate enough to remain unaware of my existence.
If anyone is interested in the DIY Nylon washer mod, I still have a few 'kits' left.
Simply send a self-addressed, pre-stamped envelope, along with $3 per neck to:
Dale Hansen
(Bessdang Gizmos)
2661 Long Hollow Pike
Hendersonville, Tn
37075-8721
It might be a good idea to drop me a line, so I know to watch for it in the mail.
Also, as of this week, there are 3 new videos about all of this stuff.
Click on my > WWW dot 'thing-a-ma-b0b' below, and it will take you right there.