Homemade Guitars Showcase

Lap steels, resonators, multi-neck consoles and acoustic steel guitars

Moderator: Brad Bechtel

Mike D
Posts: 1064
Joined: 16 Sep 1999 12:01 am
Location: Phx, Az

Post by Mike D »

Thanks Peter. Yeah it's a mahogany body and neck and what was supposed to be a violin back for the top. Rosewood fretboard with MOP inlays.
Steve Morley
Posts: 137
Joined: 24 Feb 2008 9:03 am
Location: Connecticut, USA

Post by Steve Morley »

Mike McBride wrote:Beautiful..

Let's see some crude ones too!
OK, you asked for it! Here's a tag sale beauty I found about 25 years ago. Home made pick-up (works!). I recently dug this out, and I'm trying to make up my mind if I should just play it, or enhance its rough beauty!!

Image


Image


Image
Tor Arve Baroy
Posts: 254
Joined: 12 Oct 2006 12:01 am
Location: Norway

Post by Tor Arve Baroy »

Here is one I built a couple of years ago. Its made from a combination of birch and valnut.
I made the roller nut and bridge from aluminum.
The pickup is a p90 type of unknown brand.
This picture is taken a couple of years ago, now the instrument has the signature of Al Perkins, John Beland & the Bellamy brothers on it! :-)

Image
It also has a Hipshot B-bender system on it. works great!
User avatar
Johnne Lee Ables
Posts: 398
Joined: 16 Nov 2000 1:01 am
Location: Minnesota, USA

Holly Crap!!!!! Jeez... What a talented group!!!

Post by Johnne Lee Ables »

If anyone wants to build me an 8, or more string, I'll buy the materials and pay you for your time!!!!

Jumpin' Jiminy!!!! Talent overload!!!

Johnne Lee :eek:
Justice S10-Pro 5x4 C6
Roland Cube 80GX
Wonderful Wife


"In the course of a long life a wise man will be prepared to abandon his baggage several times."
User avatar
Gary Stevenson
Posts: 324
Joined: 18 Sep 2006 12:01 am
Location: Northern New York,USA

Steve Morley's

Post by Gary Stevenson »

Being a little crude is what gives it character, sort of like a "rat bike" The pup is what is a real hoot and none the less it WORKS!I would play it out in public just for conversation it would draw!! and on a second look, I would not even wipe the dust off :lol: :lol: :lol:
User avatar
Gary Stevenson
Posts: 324
Joined: 18 Sep 2006 12:01 am
Location: Northern New York,USA

Tighe" GAS site

Post by Gary Stevenson »

Tighe you must have spent a fortune on strings alone. to keep them all playable :lol: :lol:
User avatar
Terry Farmer
Posts: 530
Joined: 28 Jun 2002 12:01 am
Location: Albuquerque, New Mexico, USA

Post by Terry Farmer »

Steve M., It would be a crime to "pretty up" that axe. I'd wipe the dust off with a wet rag and play it! Someone, at some time, put a lot of loving care into that machine.
Gary C. Dygert
Posts: 603
Joined: 2 May 2002 12:01 am
Location: Frankfort, NY, USA

Post by Gary C. Dygert »

What talent! I'm lucky I can build a fire.

Alan B, you should publish a book with photos of your creations. Of course then we'd all want soundclips, and that way lies madness.
JOZEF SMITH
Posts: 214
Joined: 15 Aug 1999 12:01 am
Location: WESTMINSTER - CA - USA

Post by JOZEF SMITH »

This is my 7 string home made oak frypan. Aluminum top and bottom plate. Aluminum bridge, pick-up made by Elva West. Strings through body using pop rivets
at top and bottom.


Image

Image
User avatar
Johnne Lee Ables
Posts: 398
Joined: 16 Nov 2000 1:01 am
Location: Minnesota, USA

Post by Johnne Lee Ables »

JOZEF SMITH wrote:This is my 7 string home made oak frypan. Aluminum top and bottom plate. Aluminum bridge, pick-up made by Elva West. Strings through body using pop rivets at top and bottom.

Hey J,

This is a WAY cool steel!

Thanks,

Johnne Lee
Justice S10-Pro 5x4 C6
Roland Cube 80GX
Wonderful Wife


"In the course of a long life a wise man will be prepared to abandon his baggage several times."
JOZEF SMITH
Posts: 214
Joined: 15 Aug 1999 12:01 am
Location: WESTMINSTER - CA - USA

Post by JOZEF SMITH »

Thanks Johnny Lee, I use this guitar a lot.
Did you notice the T logo I made. I always wanted a fry pan steel but they are way beyond my budget, so I decided to make my own. Mahalo.
Steve Morley
Posts: 137
Joined: 24 Feb 2008 9:03 am
Location: Connecticut, USA

Post by Steve Morley »

Terry Farmer wrote:Steve M., It would be a crime to "pretty up" that axe. I'd wipe the dust off with a wet rag and play it! Someone, at some time, put a lot of loving care into that machine.
Boy Terry, you said a mouthful, it does have "character"!

Several problems with it though:
The pup has v-e-r-y low output

That could be due to the fact that when the builder was fitting the pup base plate to the guitar, he hacksawed the formica cover plate, and inadvertently, cut the top off the tone circuit capacitor! [See picture] Nice Clarostat pots, though.

To get the strings off, you have to loosen all of them, and unscrew the bridge - the holes are too small to get the ball ends through! The wood screws holding the bridge on weren't holding too well, and the bridge was tipping over.

The ground from the "electronics" to the bridge, was crushed between the aluminum and the wood body, however, the insulation was never removed from the wire, therefore, lots of hum.

The headstock is a little too thick for the Kluson-style tuners, and they wobble in the holes (only two drill bits, remember?)

What I love about it is EVERY screw on it is different, and most had had a rough life before finding a home on the guitar.

The builder made do with what he/she found, and the only tools used (apparently) were 2 drill bits, a hacksaw, and 2 screwdrivers. Maybe we could have a competition to see who could build a steel with the fewest resources! The body appears to be yellow pine from the grain and color, but not as tough as some of the old growth timber.

I think I need to get it functional, replace the pup and bridge (Save them though, until I can make them work better), and get it playing. Any ideas for a bridge and pup?

Image
User avatar
George Piburn
Posts: 2045
Joined: 1 Jul 2003 12:01 am
Location: The Land of Enchantment New Mexico
Contact:

I agree with Terry ------- mostly.

Post by George Piburn »

Enlarge the Holes slightly to allow the String Balls to go through. Use a file to maintain the intergrity.

Replace the Capasitor.

Run the Ground to the Bridge.

Replacing the strings will bring up the output.

In this case Stainless Steel Strings will increase the output a bit more yet.

Don't change the PUP it is too awesome.
User avatar
Tom Pettingill
Posts: 2246
Joined: 23 Apr 2007 11:10 am
Location: California, USA (deceased)

Post by Tom Pettingill »

Steve M ... I'd first try and determine if the low output is the pickup, the connected wiring, or maybe its just mounted too low.
I'd disconnect the pickup leads from the pots and temporarily wire them strait through to the jack and see what you get.

For the bridge, you could take a step bit and open up the ball end holes. Step bits are handy and work great for reaming an existing hole.
http://www.harborfreight.com/cpi/ctaf/d ... mber=91616
On mounting, are the 2 existing screw holes stripped?
If not too bad, you could try a couple match sticks and some glue to shim it up and or a slightly longer or wider screw.
If too far gone, you can drill the hole out and plug with a section of hardwood dowel.
I'd also add at least 2 more screws to the mounting while your working on it.

Good luck with getting her going :)
Steve Morley
Posts: 137
Joined: 24 Feb 2008 9:03 am
Location: Connecticut, USA

Terry, Gary, Tom and George:

Post by Steve Morley »

I'm going to take your advice and slightly improve the existing set-up. Lots of great help here, and I appreciate it. Let me do some checking, as Tom suggested.

Tom Pettingill wrote:Steve M ... I'd first try and determine if the low output is the pickup, the connected wiring, or maybe its just mounted too low.
I'd disconnect the pickup leads from the pots and temporarily wire them strait through to the jack and see what you get.

For the bridge, you could take a step bit and open up the ball end holes. Step bits are handy and work great for reaming an existing hole.
http://www.harborfreight.com/cpi/ctaf/d ... mber=91616
On mounting, are the 2 existing screw holes stripped?
If not too bad, you could try a couple match sticks and some glue to shim it up and or a slightly longer or wider screw.
If too far gone, you can drill the hole out and plug with a section of hardwood dowel.
I'd also add at least 2 more screws to the mounting while your working on it.

Good luck with getting her going :)
User avatar
CrowBear Schmitt
Posts: 11624
Joined: 8 Apr 2000 12:01 am
Location: Ariege, - PairO'knees, - France
Contact:

Post by CrowBear Schmitt »

Matt & his family lumber mill from France made these

Image

Image
User avatar
Tom Pettingill
Posts: 2246
Joined: 23 Apr 2007 11:10 am
Location: California, USA (deceased)

Post by Tom Pettingill »

Those look great CrowBear :)
Are the bridges left radiused or are the saddles ground down and flattened?
User avatar
Roger Palmer
Posts: 190
Joined: 12 Nov 2008 3:54 pm
Location: Rossendale, UK

Post by Roger Palmer »

Image
Image

Thought I'd bump this thread with a couple of pictures of my latest build

Its made from European Ash, Abalone markers, rosewood frets and has an Irongear Jailhouse Rail pickup that is coil split. The pickup ring is made from walnut and the nut and bridge are aluminium

22.5 scale, it plays nicely and I love its overall small size.

The pickup is pretty hot and I'm still working out the best height for it
User avatar
James Kerr
Posts: 1674
Joined: 16 Feb 2008 7:40 am
Location: Scotland, UK

Post by James Kerr »

Here is my efforts, a National Dynamic Replica.


Image

And a National New Yorker about to be finished, it has a Lace Alumitone Pickup and will have 2/3 palm levers fitted to the Bigsby unit.


Image


You can listen by going to MySpace.

James.

Image
Kevin Macneil Brown
Posts: 210
Joined: 29 Jan 2002 1:01 am
Location: Montpelier, VT, USA
Contact:

Post by Kevin Macneil Brown »

What a feast of imagination, ingenuity, and artful execution this thread is. Amazing!
User avatar
Don Kona Woods
Posts: 2726
Joined: 11 Dec 2004 1:01 am
Location: Hawaiian Kama'aina

Post by Don Kona Woods »

Danny James,
Thats a fine looking Ric style lapsteel Don.

Somebody beat me to it. I was thinking seriously of building my next one with a changer in it similar to the one you have.

Oh well I probably will go ahead and do it anyway
.

Your thinking is getting more straight all the time, Danny. When you build this guitar, bring it to Winchester and show me. I am from Missouri. ;-) ;-)

Aloha, :)
Don
Danny James
Posts: 694
Joined: 3 May 2004 12:01 am
Location: Summerfield Florida USA

Post by Danny James »

Don, I'm working on a changer now and hope to cut out the guitar body this week. It won't be ready for Winchester this year though.

There are two fry pans on page 4 here that I really like the looks of too. Jozeph Smith's, and Roger palmers. I may cut out the blanks for all three while I'm at it. I still have enough "Wild Cherry to do the job. Maybe go for a horseshoe style pick up too, while I'm at it. Have to find a source for that yet?? ;-) :idea:
User avatar
Mark Daniels
Posts: 75
Joined: 28 Jun 2009 2:07 pm
Location: United Kingdom

Post by Mark Daniels »

Encouraged by this thread, I've decided to have a go at making an 8 string lap steel.

I understand the setup and maintenance of guitars, but I possess next to no woodworking skills :cry: However, if I plan carefully and take my time, I think I can make a playable instrument.

My wife thinks that I can make a good job and it's great to have that encouragement. :D
User avatar
Alan Brookes
Posts: 13218
Joined: 29 Mar 2006 1:01 am
Location: Brummy living in Southern California

Post by Alan Brookes »

Mark Daniels wrote:...My wife thinks that I can make a good job and it's great to have that encouragement. :D
Go for it, Mark. A lap steel is only a plank with a pickup and strings. Anything beyond that is art. You don't need to be a skilful woodworker to build one. :D ;-) ;-) ;-) :wink:
User avatar
Tom Pettingill
Posts: 2246
Joined: 23 Apr 2007 11:10 am
Location: California, USA (deceased)

Post by Tom Pettingill »

Encouraged by this thread, I've decided to have a go at making an 8 string lap steel.
Like Alan said, go for it! Its a fun and rewarding experience. If you get stuck on anything, there is a lot of friendly help here at your disposal :)
Post Reply