| Author |
Topic: Mullen pedal bar |
Willis Vanderberg
From:
Petoskey Mi
|
Posted 16 Feb 2007 9:18 am |
|
I have a D-10 Mullen , 1996 model. I have had the pedal bar come loose at the left end or at the A, B. C, pedal end if you will. Is this a common problem ? I am now using a little extra torque on the wing nut.
Is the proper way to install this bar, seat it against the leg collars ? There is a gap between the bar and the rubber crutch tip. I know some have drilled this and put a bolt in the bar through the leg. Another has put steel washers on the leg on top of the cruch tip rubber,and seated the pedal bar against that.
I have owned a lot of pedal guitars and don't remember ever having this problem. |
|
|
|
Joseph Solomon
From:
Newtown, Pennsylvania, USA
|
Posted 16 Feb 2007 10:09 am Mullen Pedal Bar
|
|
| Willis I had a similar problem with my pedal bar riding up. I installed a hose clamp on the leg on top of the bar. It doesn't look too good cosmetically, but it solved the problem. |
|
|
|
Brint Hannay
From:
Maryland, USA
|
Posted 16 Feb 2007 10:31 am
|
|
I was going to post about the same thing. I have a 1994 Mullen D-10, and when I pick it up to move it the pedal rack slides down on the right side. The first time I press a pedal, it kind of jacks the rack back up. I tighten the wing nuts as tight as I can, but it still happens.
On every other steel I've had, I've set the legs so the pedal rack just fits in between the clutch and the rubber foot, but the Mullen leg won't retract that far. There's about 1/4" of extra length below the clutch when it's fully retracted. I don't know why the leg would be made that way. I plan to have the inner section of the leg cut down so a "normal" fit is possible. |
|
|
|
David Nugent
From:
Gum Spring, Va.
|
Posted 16 Feb 2007 4:23 pm
|
|
| I purchased longer rubber tips from a hardware store when I had my older Mullen, solved the problem rather neatly. |
|
|
|
Howard Tate
From:
Leesville, Louisiana, USA, R.I.P.
|
Posted 16 Feb 2007 4:55 pm
|
|
| I've never had the problem with my Mullen but it happened with my Carter. I think it can happen to any guitar with that type clamp. My Zum had a bolt that went through the leg. |
|
|
|
Tommy Young
From:
Ethelsville Alabama
|
Posted 16 Feb 2007 6:40 pm leg clamp
|
|
| what i did to solve the problem is longer rubber boots and went to lowes and found some 1/4 flat bar knobs to put instead of the wing nuts and since no mo slips just what i did tommy |
|
|
|
Jerry Overstreet
From:
Louisville Ky
|
Posted 16 Feb 2007 10:58 pm
|
|
| Bud, I used a file, sandpaper or maybe a grinder [can't remember offhand right now] to remove a little bit of the material from the clamp[ so that the block would clamp tight before the wing nut bottomed out. Haven't had any problem since. |
|
|
|
Willis Vanderberg
From:
Petoskey Mi
|
Posted 17 Feb 2007 5:21 pm
|
|
Thanks for al the replies. I am still looking at the situation and I will come up with a fix.
Bud |
|
|
|
Justin Griffith
From:
Taylor, Texas, USA
|
Posted 17 Feb 2007 6:46 pm
|
|
| Sounds like Brint has the right fix. Take the inner (smaller) leg out and cut it off an inch or two, then the leg will adjust properly. |
|
|
|
