peavy 112 problem
Moderator: Shoshanah Marohn
-
- Posts: 4261
- Joined: 26 Apr 2004 12:01 am
- Location: Ona, Florida, USA, R.I.P.
peavy 112 problem
HELLO MIKE,i'm having problem with new amp.it sounds great,but starts feed back roar at number 5 volume.i've traded cords,pedal, guitars all i can think of,put amp in back,front,ect.but it goes to howling louder and louder.until i stop playing , then it will calm down. i'm hooking up guitar to amp, out of loop with volume pedal.don't know what else to do.
farris
farris
- John Daugherty
- Posts: 2188
- Joined: 13 May 2004 12:01 am
- Location: Rolla, Missouri, USA
- Contact:
Ferris, mine always sounds like that when I am playing and stops when I quit !!!
Now to get serious.. maybe your pickup is too hot to be fed directly to the input. I think you are getting feedback from the speaker to the guitar body. A microphonic pickup would make this worse.
Try connecting guitar through volume pedal to input of amp. That is how I run my NV112.
I connect my effects to the post gain jacks.
It works great for me.
Let me know what you find, old buddy, and keep the possums out of the amp cabinet.........JD
Now to get serious.. maybe your pickup is too hot to be fed directly to the input. I think you are getting feedback from the speaker to the guitar body. A microphonic pickup would make this worse.
Try connecting guitar through volume pedal to input of amp. That is how I run my NV112.
I connect my effects to the post gain jacks.
It works great for me.
Let me know what you find, old buddy, and keep the possums out of the amp cabinet.........JD
- Darvin Willhoite
- Posts: 5715
- Joined: 4 Aug 1998 11:00 pm
- Location: Roxton, Tx. USA
Sometimes reverb units can cause this, have you tried playing with the reverb off to see if it still does it? I had this happen on a Mesa Boogie amp.
------------------
Darvin Willhoite
Riva Ridge Recording
------------------
Darvin Willhoite
Riva Ridge Recording
-
- Posts: 4261
- Joined: 26 Apr 2004 12:01 am
- Location: Ona, Florida, USA, R.I.P.
John i tryed it both ways no difference,Darwing i hadn't turned the reverb off but i will try that next.i will have it out again tomorrow, so we see what happens. gets to howling so loud it drowns my playing out.i hooked up just like book says, steel to amp, then in and out with pedal.man i'm sick right now.tone is fine,but can't out play the howl. farris
- John Daugherty
- Posts: 2188
- Joined: 13 May 2004 12:01 am
- Location: Rolla, Missouri, USA
- Contact:
- Larry Robbins
- Posts: 3521
- Joined: 18 Feb 2003 1:01 am
- Location: Fort Edward, New York
-
- Posts: 200
- Joined: 2 Oct 2001 12:01 am
- Location: Macedon, NY, USA
- Fred Shannon
- Posts: 3363
- Joined: 27 Sep 2002 12:01 am
- Location: Rocking "S" Ranch, Comancheria, Texas, R.I.P.
- Contact:
Farris I have the same problem. Check your reverb setting. Mine will start the hum at position 4 o f the reverb knob setting. I can set it back to 3 or 3.5 and it stops. I called Mike about it and was told to take it to a Peavey rep. Not too easy here, over a 150 mile round trip. I'm just living with it right now.
phred
------------------
"From Truth, Justice is Born"--Quanah Parker-1904
phred
------------------
"From Truth, Justice is Born"--Quanah Parker-1904
-
- Posts: 5857
- Joined: 4 Aug 1998 11:00 pm
- Location: Oceanside, Calif, USA
- Contact:
- John Daugherty
- Posts: 2188
- Joined: 13 May 2004 12:01 am
- Location: Rolla, Missouri, USA
- Contact:
- Jack Stoner
- Posts: 22087
- Joined: 3 Dec 1999 1:01 am
- Location: Kansas City, MO
Ahh! I use a Pod XT for effects and don't use the reverb in my 112. However, I did use it one time at home, doing some comparisons with my Nashville 1000 and doing some tests using both amps, and didn't notice any feedback problems with the reverb.
We haven't heard back on whether turning off the reverb solves the problem, and until we do we can't assume that is what is causing this particular problem.
We haven't heard back on whether turning off the reverb solves the problem, and until we do we can't assume that is what is causing this particular problem.
-
- Posts: 5027
- Joined: 4 Aug 1998 11:00 pm
- Location: Meridian, Mississippi USA
-
- Posts: 87
- Joined: 23 Nov 2004 1:01 am
- Location: Corsicana, Texas, USA
-
- Posts: 6870
- Joined: 27 Nov 2000 1:01 am
- Location: Oklahoma City, OK USA, (deceased)
- Contact:
I have been considering buying a 112 because of the weight and convenience but the above posts indicate that it has a spring reverb.
I have had my problems on stage with a spring reverb (Session 500) and can't help but wonder if the same problem will occur with the 112 when someone walks or dances across the stage?
....any comments from those with experience?
www.genejones.com
I have had my problems on stage with a spring reverb (Session 500) and can't help but wonder if the same problem will occur with the 112 when someone walks or dances across the stage?
....any comments from those with experience?
www.genejones.com
- Jack Stoner
- Posts: 22087
- Joined: 3 Dec 1999 1:01 am
- Location: Kansas City, MO
Normally the reverb spring won't cause noise on a "normal" stage unless it's old and weak and is sagging.
I had a Session 500 that developed that after about 12 years of "heavy" use, replaced the reverb pan and no more problems.
I've got a 112 that I sit on an Amp stand. I don't normally use the reverb as I use a POD XT for reverb and delay. But I've tried it on occasion, on stage, and there wasn't any noise. I wouldn't even consider that an issue with a new amp.
I had a Session 500 that developed that after about 12 years of "heavy" use, replaced the reverb pan and no more problems.
I've got a 112 that I sit on an Amp stand. I don't normally use the reverb as I use a POD XT for reverb and delay. But I've tried it on occasion, on stage, and there wasn't any noise. I wouldn't even consider that an issue with a new amp.
-
- Posts: 411
- Joined: 25 Nov 2002 1:01 am
- Location: California Central Coast
-
- Posts: 4261
- Joined: 26 Apr 2004 12:01 am
- Location: Ona, Florida, USA, R.I.P.
sorry guys,i been down in the hips and back, bad,tomorrow i find out for sure,taking it out front,turn it up and i will reply tomorrow night.gonna get to the bottom of this for sure, or blow it up. i will try all i know, change guitars, pedals, pickups, cords ect. sorry i have delayed but i've really been down.sorry didn't mean to put this topic off. farris
-
- Posts: 4385
- Joined: 10 May 2004 12:01 am
- Location: San Antonio, Texas, USA
- Jerry Roller
- Posts: 10319
- Joined: 17 Apr 1999 12:01 am
- Location: Van Buren, Arkansas USA
- Contact:
I have two Nashville 112's and I do not know of any amp that I would be willing to trade even for if I could not get another 112. Well, maybe a new Standel but certainly nothing costing under $1000.00. Mike can help if you have a problem if you will give him a chance.
Jerry<font size="1" color="#8e236b"><p align="center">[This message was edited by Jerry Roller on 06 April 2005 at 04:49 PM.]</p></FONT>
Jerry<font size="1" color="#8e236b"><p align="center">[This message was edited by Jerry Roller on 06 April 2005 at 04:49 PM.]</p></FONT>
-
- Posts: 2696
- Joined: 8 May 2000 12:01 am
- Location: queens, new york city
Gene, I've played on a number of stages with a 112 and have noticed no such problem. As far as any opinions about the sound, it has been endorsed by quite a number of pros.<SMALL>the same problem will occur with the 112 when someone walks or dances across the stage?</SMALL>
------------------
Jeff's Jazz
-
- Posts: 63
- Joined: 20 May 2002 12:01 am
- Location: Oklahoma
Farris:
Some thoughts for you. About two weeks ago - at the end of a gig - I noticed a strange "hum" coming from my N112. I thought at the time that it was a bad cord- so, I basically ignored it.
When setting up early last night, the hum was still there. I tried every possible combination of setups,cords, etc. - but, the problem did not go away. When my bandmates arrived, I hooked-up to one of their amps (an old Fender Twin)- the hum was still there.
So, we connected his guitar to my N112 - NO hum. After doing some further checking, we found that there is a problem with the grounding in my input jack/pickup. This might not be anything at all related to what you are experiencing -- but, thought I would mention what I had run into.
Some thoughts for you. About two weeks ago - at the end of a gig - I noticed a strange "hum" coming from my N112. I thought at the time that it was a bad cord- so, I basically ignored it.
When setting up early last night, the hum was still there. I tried every possible combination of setups,cords, etc. - but, the problem did not go away. When my bandmates arrived, I hooked-up to one of their amps (an old Fender Twin)- the hum was still there.
So, we connected his guitar to my N112 - NO hum. After doing some further checking, we found that there is a problem with the grounding in my input jack/pickup. This might not be anything at all related to what you are experiencing -- but, thought I would mention what I had run into.
-
- Posts: 402
- Joined: 29 Jul 1999 12:01 am
- Location: Baytown, Texas, USA
I had a hum problem on my NV112 when the reverb was turned up to around 4 or more...
Found that it is very sensitive to a wall wart being too close to the rear bottom of the amp...or at some points on the top..
also readjusted the reverb as far to the rear of the amp as possible...also reversed the reverb wires connection points which helped.... It much better altho I usually don't my reverb past 3 ot so.......
Found that it is very sensitive to a wall wart being too close to the rear bottom of the amp...or at some points on the top..
also readjusted the reverb as far to the rear of the amp as possible...also reversed the reverb wires connection points which helped.... It much better altho I usually don't my reverb past 3 ot so.......
-
- Posts: 4261
- Joined: 26 Apr 2004 12:01 am
- Location: Ona, Florida, USA, R.I.P.
can't believe the wonderful responses!!well i got down in my hips and back for 4 days,so i just got back on trying some more.
Latest,i won't to say,wow what a little amp.
I bought a T T pickup from Jerry Wallace,he wound it to 18,000.put it in yesterday,put on new strings,Tommy White Jags,set the pickup way down,went out in the shop,hooked up Hilton pedal.put the Peavy 112 on number 5 volume,reverb on number 4,that is the sweetest sounding amp i've played in a long time. now if i put reverb on number 5 it will feed back bad. and way,most of us don't even use the reverb from amp.but number 4 is plenty for most anyone anyway.next time out i will turn reverb off and hook up my Boss dd3 and delay,but i will say to all that this is a fine little set up now.and i'm using a little pro1 SHO-BUD. GOD bless you all, great friends
farris
Latest,i won't to say,wow what a little amp.
I bought a T T pickup from Jerry Wallace,he wound it to 18,000.put it in yesterday,put on new strings,Tommy White Jags,set the pickup way down,went out in the shop,hooked up Hilton pedal.put the Peavy 112 on number 5 volume,reverb on number 4,that is the sweetest sounding amp i've played in a long time. now if i put reverb on number 5 it will feed back bad. and way,most of us don't even use the reverb from amp.but number 4 is plenty for most anyone anyway.next time out i will turn reverb off and hook up my Boss dd3 and delay,but i will say to all that this is a fine little set up now.and i'm using a little pro1 SHO-BUD. GOD bless you all, great friends
farris
-
- Posts: 5027
- Joined: 4 Aug 1998 11:00 pm
- Location: Meridian, Mississippi USA
Farris, try moving the vinyl bag which contains the reverb pan away from the speaker. Also, make sure that the bag fits as loosely as possible around the pan. If this doesn't work, please call me and I will assist in resolving this for you. Toll free at 1-877-732-8391, ext. 1180 from 8am to 5pm CST Monday through Friday. I'll await your call.
Mike Brown
Peavey Electronics Corporation
Mike Brown
Peavey Electronics Corporation
- Fred Shannon
- Posts: 3363
- Joined: 27 Sep 2002 12:01 am
- Location: Rocking "S" Ranch, Comancheria, Texas, R.I.P.
- Contact:
Well surprise. My Peavey 112 is humming like a smooth running watch. I spent some time with Mike Brown on the number listed in this thread and after a short time a minor problem was corrected and everything is super. Best amp I've ever used for Steel and the reverb is tremendous. This means i dont have to wag around a Lexicon or even the RV3. This reverb is good enough for this old cowpoke.
Wonder how many more amp manufacturers have a Mike Brown on board who specializes in Steel guitar? Well Duh!!
phred
------------------
"From Truth, Justice is Born"--Quanah Parker-1904
Wonder how many more amp manufacturers have a Mike Brown on board who specializes in Steel guitar? Well Duh!!
phred
------------------
"From Truth, Justice is Born"--Quanah Parker-1904