| Author |
Topic: Nashville 400. Does it have mod? |
Ron Randall
From:
Dallas, Texas, USA
|
Posted 21 Apr 2002 11:17 am |
|
I have a second hand Peavey Nashville 400.
Serial number 4A-01955758.
How can I tell if it has the mod kit?
------------------
Fender Stringmaster T-8
PV N400
Dobro squareneck
Dobro roundneck
Lots of Taylors
|
|
|
|
Bob Knight
From:
Bowling Green KY
|
Posted 21 Apr 2002 11:56 am
|
|
Nashville 400 amplifiers with serial numbers higher than 08575482 do not require the installation of this modification kit as this kit has been incorporated into the circuit at the factory. Serial numbers prior to the above are not modified.
The above information was obtained from: www.peavey.com |
|
|
|
Ron Randall
From:
Dallas, Texas, USA
|
Posted 22 Apr 2002 6:07 am
|
|
| How can I tell IF it has a mod installed? |
|
|
|
Mike Brown
From:
Meridian, Mississippi USA
|
Posted 22 Apr 2002 8:49 am
|
|
Thanks for your assistance, Bob.
Ron, if you would like to purchase any of the Peavey steel guitar amp kits, you may contact our parts department at (601)483-5365 to order. The kit number for the Nashville 400 is 90500048. Other kits that are available are for the Vegas 400, Session 400 Limited, Session 500 and the Profex II.
Mike Brown
Peavey Electronics Corporation
|
|
|
|
Jim Smith
From:
Midlothian, TX, USA
|
Posted 22 Apr 2002 9:21 am
|
|
| I think Ron doesn't know if the mod has been installed on his amp and is wanting to know what to look for so he can tell if the amp has already had the mod kit installed, i.e. a chip with a different part number, etc. |
|
|
|
Fred Murphy
From:
Indianapolis, In. USA
|
Posted 22 Apr 2002 6:03 pm
|
|
| If you know of anyone who has a modified amp, you could try it out. There is a tremendous difference in tone quality and after you have used one you can easily tell the difference. To me an unmodified one sounds cold and hard, with a lot of mid sound, and one with a mod will sound full and vibrant, much more like a tube amp. If you wished to take the amp apart, you could probably be able to see that some of the resistors and capacitors had been resoldered as the solder will probably not be as shiny as the factory soldering. |
|
|
|
Bill Terry
From:
Bastrop, TX
|
Posted 22 Apr 2002 8:58 pm
|
|
Take it apart and look at the opamps (the 8 pin 'chips') If they're 4558's it most likely doesn't have the mod.
------------------
Home Page
|
|
|
|
Ron Randall
From:
Dallas, Texas, USA
|
Posted 24 Apr 2002 3:09 pm
|
|
Thank you Bill Terry.
That is the question, and your answer helps. Now I know what to look for.
|
|
|
|
Brian Lethert
From:
Minneapolis, Minnesota, USA
|
Posted 24 Apr 2002 4:13 pm
|
|
Is the mod for the nashville 400 something that someone with previous circuit board repair experience could eaaasily do themselves? About how much does the mod cost?
Brian Lethert
|
|
|
|
Bill Terry
From:
Bastrop, TX
|
Posted 24 Apr 2002 5:31 pm
|
|
Brian, yep... bunch a thru-hole R's and C's and the op-amps, which are socketed. The kit comes with a board layout and schematic so it's a snap. The biggest hassle is getting the amp apart. Don't know about the cost... call Peavey, the service dept. is real hip.
------------------
Home Page
|
|
|
|
