Bridging a resistor on volume pedals
Moderator: Shoshanah Marohn
- Doug Jones
- Posts: 1561
- Joined: 4 Aug 1998 11:00 pm
- Location: Oregon & Florida
Bridging a resistor on volume pedals
In an attempt to get crisper lows, I've sought advice from some folks. I've tried thinner sounding pickups, matchbox, etc. Just recently I received a recommendation to place a 500K resistor on the hot and ground either at the output jack of the steel or at the input of the volume pedal. I got a 470K 1/2 Watt resistor and put it on the inbound hot and ground of the 500K pot in my volume pedal. It thinned it out (both highs and lows) and seemed to increase the volume. It also seemed to tighten up the overall tone. Any comments from you tech-wiz-bang folks?
-
- Posts: 1834
- Joined: 4 Aug 1998 11:00 pm
- Location: Goodlettsville, TN , Spending my kid's inheritance
- Contact:
Doug....
As an Electronic tech,I think anytime you place a resistance or capactiance in front of the amp,you only decrease the output of the P/U. Now,as most of us know,we desire the max signal from the instrument. Therefore,we can EQ it or trim to fit our needs at the amp. To reduce the primary signal from the P/U isn't such a bright idea.
O.K..... This info is for the "passive" V/C pedals only !!! Any "powered" pedal such as the "Hilton" or "Goodrich" pedal has pre-amp circuits build-in. (In this case,you don't need to worry about this problem) I am a great believer in the "Myrick" mode of a passive pedal. This modification attempts to present the max signal to the amp at any volumne level.
As an Electronic tech,I think anytime you place a resistance or capactiance in front of the amp,you only decrease the output of the P/U. Now,as most of us know,we desire the max signal from the instrument. Therefore,we can EQ it or trim to fit our needs at the amp. To reduce the primary signal from the P/U isn't such a bright idea.
O.K..... This info is for the "passive" V/C pedals only !!! Any "powered" pedal such as the "Hilton" or "Goodrich" pedal has pre-amp circuits build-in. (In this case,you don't need to worry about this problem) I am a great believer in the "Myrick" mode of a passive pedal. This modification attempts to present the max signal to the amp at any volumne level.
- Jack Stoner
- Posts: 22087
- Joined: 3 Dec 1999 1:01 am
- Location: Kansas City, MO
Placing a resister across the input/output effectively decreases the resistance of the volume control pot. The sum of two resistors in parallel that are the same value is 1/2 the resistance amount of one and in this case by placing the 470K resistor in Parallel with the 500K (when it is at the max resistance point in it's travel) you have reduced the overall resistance to approximately half.
The "Myrick" mod to the volume pedal is a similar mod but uses another 500K volume control pot.
The volume pedal should not have that much affect on your tone. It can have some affect but not what you are looking for.
I use Lawrence 710 pickups on my Franklin, a stock Goodrich 120 volume pedal (500K pot model) and in conjunction with how I set the EQ on my Nashville 400 I can get the lower strings on my C6th neck to be "crisp". I don't get the treble my Telecaster is capable of but then I don't want that much treble on my steel.
I think the answer to what you want is more in the amp than in the guitar or volume pedal. One other thing that will have a major affect on tone or frequency response is the cords. You have to have decent cords or everything else you do won't count. I use to use Belden 8410 cable, which is a high quality shielded audio cable, for my cords and I thought it worked good until I bought some George L's cables. It took me 10 minutes with the George L's cables and the Belden was history.
The "Myrick" mod to the volume pedal is a similar mod but uses another 500K volume control pot.
The volume pedal should not have that much affect on your tone. It can have some affect but not what you are looking for.
I use Lawrence 710 pickups on my Franklin, a stock Goodrich 120 volume pedal (500K pot model) and in conjunction with how I set the EQ on my Nashville 400 I can get the lower strings on my C6th neck to be "crisp". I don't get the treble my Telecaster is capable of but then I don't want that much treble on my steel.
I think the answer to what you want is more in the amp than in the guitar or volume pedal. One other thing that will have a major affect on tone or frequency response is the cords. You have to have decent cords or everything else you do won't count. I use to use Belden 8410 cable, which is a high quality shielded audio cable, for my cords and I thought it worked good until I bought some George L's cables. It took me 10 minutes with the George L's cables and the Belden was history.
- Jack Stoner
- Posts: 22087
- Joined: 3 Dec 1999 1:01 am
- Location: Kansas City, MO
-
- Posts: 3730
- Joined: 1 May 1999 12:01 am
- Location: 248 Laurel Road Ozark, Missouri 65721
- Contact:
Doug, I don't see how the resistor, wired as you described, would help the frequency response of your pickup. I've tried many combinations of resistors and capacitors across a pot. The keys to good sound is making sure the pickup sees high impedance and low capacitance. Like Jack told you, hookup cords make a big difference when using a pot pedal.
-
- Posts: 21
- Joined: 30 Mar 2001 1:01 am
- Location: Lexington, KY
-
- Posts: 21192
- Joined: 16 Feb 1999 1:01 am
- Location: Glen Burnie, Md. U.S.A.
- Doug Jones
- Posts: 1561
- Joined: 4 Aug 1998 11:00 pm
- Location: Oregon & Florida
Thanks for all your responses. I A/B'd both of my Zum pedals which have 500K pots; one with the resistor and the other without. There was a definate tone loss; kind of a washed out sound if there's such a description. For the record, I use Carol C-1300 oxygen-free audio cable with Swithcraft plugs. My stage rig is a '92 Lashley, a modified Goodrich 4a Matchbox, Evans preamp, Lexicon Alex, Ibanez DD-1000, Korg DTR-1 and 2 Evans FET-500LVs (power sections only). I'm going back to my regular vol. pedal set up.
- Doug Jones
- Posts: 1561
- Joined: 4 Aug 1998 11:00 pm
- Location: Oregon & Florida
-
- Posts: 491
- Joined: 8 Jun 1999 12:01 am
- Location: Wylie, TX US
I agree with the responses. The lowering of the effective pot impedance will only reduce highs and amplitude unless of course you have an active setup.
HOWEVER, the placement of a resistor across a pot will change its taper. It adds a hyperbolic term to the taper. In fact, if you are out of town and are in a pinch for a volume pot and all you can find is like a 1 Megohm linear, you can put another 1 Megohn or 500K fixed resistor across it and approximate a audio taper pot. Of course this is not optimial, but it brings it closer to a base 10 logarithmic response. I have some graps in Excel that shows that if you would like to see them.
An audio taper pot is not the same as a logarithmic pot. The audio taper pot is a logarithmic taper with the asymptotic extents rounded off.
Just thought I'd throw that in. I was curious a long time ago about a fixed resistor across a pot, so I graphed it to see.
Good post.
------------------
Terry Downs
http://nightshift.net
terry@nightshift.net
HOWEVER, the placement of a resistor across a pot will change its taper. It adds a hyperbolic term to the taper. In fact, if you are out of town and are in a pinch for a volume pot and all you can find is like a 1 Megohm linear, you can put another 1 Megohn or 500K fixed resistor across it and approximate a audio taper pot. Of course this is not optimial, but it brings it closer to a base 10 logarithmic response. I have some graps in Excel that shows that if you would like to see them.
An audio taper pot is not the same as a logarithmic pot. The audio taper pot is a logarithmic taper with the asymptotic extents rounded off.
Just thought I'd throw that in. I was curious a long time ago about a fixed resistor across a pot, so I graphed it to see.
Good post.
------------------
Terry Downs
http://nightshift.net
terry@nightshift.net
- Jack Stoner
- Posts: 22087
- Joined: 3 Dec 1999 1:01 am
- Location: Kansas City, MO
-
- Posts: 3730
- Joined: 1 May 1999 12:01 am
- Location: 248 Laurel Road Ozark, Missouri 65721
- Contact:
OK Jack, if the Oxygen Free doesn't do anything for you, Bobbe Seymour has "GOLD" connection cords. Bobbe Seymour was telling me about the recording studio he had, and it had solid GOLD hookup cords. Think of it Jack, solid GOLD, the sound would just have to be better! I am smiling Jack!<FONT SIZE=1 COLOR="#8e236b"><p align=CENTER>[This message was edited by Keith Hilton on 14 April 2001 at 08:45 PM.]</p></FONT>
-
- Posts: 7418
- Joined: 12 Jan 2001 1:01 am
- Location: Hendersonville TN USA, R.I.P.
- Contact:
-
- Posts: 21192
- Joined: 16 Feb 1999 1:01 am
- Location: Glen Burnie, Md. U.S.A.
Doug, I don't know what kind of "sound" you're looking for, but it sounds like you've got enough "stuff" between your axe and the amp to confuse even an electron! Do you really need all that "stuff" to sound good?
If I had to guess, I'd say that all that "stuff" might be part of the problem you're complaining about...just a thought.
If I had to guess, I'd say that all that "stuff" might be part of the problem you're complaining about...just a thought.
-
- Posts: 3730
- Joined: 1 May 1999 12:01 am
- Location: 248 Laurel Road Ozark, Missouri 65721
- Contact:
- Jack Stoner
- Posts: 22087
- Joined: 3 Dec 1999 1:01 am
- Location: Kansas City, MO
Although I personally consider gold connectors for instrument cables to be a marketing pitch, gold is an excellent conductor. Plug in printed circuit boards with printed edge connectors which are usually plugged in, many for years, are a prime application of gold connectors as they do not oxidize or exhibit flakey connections as easy as other metal compounds including silver.
For guitar cords or patch cords that are being plugged in and unplugged frequently, good grade standard connectors such as the Switchcraft 280 1/4" plug, George L's plugs, more than suffice. The connection resistance on this type of plug is negligible.
For guitar cords or patch cords that are being plugged in and unplugged frequently, good grade standard connectors such as the Switchcraft 280 1/4" plug, George L's plugs, more than suffice. The connection resistance on this type of plug is negligible.
-
- Posts: 3730
- Joined: 1 May 1999 12:01 am
- Location: 248 Laurel Road Ozark, Missouri 65721
- Contact:
-
- Posts: 1834
- Joined: 4 Aug 1998 11:00 pm
- Location: Goodlettsville, TN , Spending my kid's inheritance
- Contact:
How did we know that ???<SMALL>Ok, I was doing a little joking,kidding and having a little fun. </SMALL>
(personally, I too think "Gold" is a sells ploy)
Too many times tho,the un-informed has trouble with seperatin' the jokes from the truth.
On a one to one basis, I dought very few people can tell the difference between "gold" and plain "metal".
- Mark Herrick
- Posts: 1154
- Joined: 4 Aug 1998 11:00 pm
- Location: Bakersfield, CA
- Jack Stoner
- Posts: 22087
- Joined: 3 Dec 1999 1:01 am
- Location: Kansas City, MO
-
- Posts: 21192
- Joined: 16 Feb 1999 1:01 am
- Location: Glen Burnie, Md. U.S.A.
- Blake Hawkins
- Posts: 1844
- Joined: 4 Aug 1998 11:00 pm
- Location: Florida
Donny is right on the brass audio plugs.
Over 45 years of making my living in broadcast facilities and recording studios,
I've handled more audio patches and plugs than I can count.
Professional audio patch panels use unplated brass plugs. In order to keep the noise down they need to be cleaned on a regular basis.
The problem wasn't too bad with 1/4" phone
patch plugs, but when the industry started going to the smaller "tiny-jacks" which had much less contact area, the required cleaning interval was quite a bit shorter.
I did work with an audiophile engineer who maintained that he could tell the difference in sound between gold, silver, and cadmium plated connectors. He did not like the sound of the gold ones. However, he never did demonstrate this ability to me.
One time when we ran short, I put some gold ones in the system. He didn't know they were there until one of the other engineers told him.
Over 45 years of making my living in broadcast facilities and recording studios,
I've handled more audio patches and plugs than I can count.
Professional audio patch panels use unplated brass plugs. In order to keep the noise down they need to be cleaned on a regular basis.
The problem wasn't too bad with 1/4" phone
patch plugs, but when the industry started going to the smaller "tiny-jacks" which had much less contact area, the required cleaning interval was quite a bit shorter.
I did work with an audiophile engineer who maintained that he could tell the difference in sound between gold, silver, and cadmium plated connectors. He did not like the sound of the gold ones. However, he never did demonstrate this ability to me.
One time when we ran short, I put some gold ones in the system. He didn't know they were there until one of the other engineers told him.
- Jack Stoner
- Posts: 22087
- Joined: 3 Dec 1999 1:01 am
- Location: Kansas City, MO
I was a Tech Controller in the Air Force. Patch panels was one of the things Tech Controllers used to test and substitue teletypes and other comm equipment. The military PL55 and PJ068 and later the smaller plugs Blake referred to were on a regular monthly PM schedule for cleaning. We used steel wool and brasso to keep them clean.
The telephone companies used the brass plugs in their manual patch panels for years. They still use them today in their analog test equipment.
The telephone companies used the brass plugs in their manual patch panels for years. They still use them today in their analog test equipment.