Tone Bar Selection: Small/lighter vs. Large/heavier

David DeLoach · From: Tennessee, USA

I have a few tone bars but my go-to to is the Dunlap 919 (4.5 oz. - 3/4" x 2-3/4"). I like it for the maneuverability the smaller/lighter bar has.

But I find a larger/heavier bar such as the Dunlap 921 (11.5 oz. - 1" x 3-3/4") gives me a better tone and sustain.

I recently got a Clinesmith thermoplastic tone bar (4.5 oz. - 3/4" x 3") that I really like. Less noise and very easy to move around with.

I'm curious what you guys are using.

I'm also curious if any of you found the heavier bars more difficult to use at first, but persevered with them until they became easy to jump around the neck with.

_________________
https://www.MasterGuitarists.com/

Glenn Wilde · From: California, USA

I've got a pile about like you do, and I use them all occasionally, but right now I'm really loving a glass 3" x 1" made by Silica Sound, it's big but only has a brass slug in the middle so it's quite a bit lighter than my stainless ZB of the same size. I've been finding the 1" bars way easier to hold.

Bill Groner · From: QUAKERTOWN, PA

I'm kinda am partial to the ones I make. Wink

_________________
Currently own, 6 Groner-tone lap steels, one 1953 Alamo Lap steel, Roland Cube, Fender Champion 40

Cody Farwell · From: Sunland, CA

Bill Groner · From: QUAKERTOWN, PA

No Cody, I use the threads in the polishing process. The slug is stationary.
_________________
Currently own, 6 Groner-tone lap steels, one 1953 Alamo Lap steel, Roland Cube, Fender Champion 40

Rick Aiello · From: Berryville, VA USA

I love the backside indent ... Mr. Green

Jack Hanson · From: San Luis Valley, USA

I too have so many tone bars I likely couldn't count 'em, and if I put 'em all in a bucket I probably couldn't lift it. But for years, my go-to bar has been the standard stainless Latch Lake (formerly Broz-O-Phonic) 3/4" x 3" bar from Eagan, MN.

https://latchlakemusic.com/slides/hawaiian-bar/

Carey Hofer · From: South Dakota, USA

I have tried several on my 8 string Rukavina lapsteel. Of the three Dunlop bars I tried I like the 918 the best. Not too short or too heavy. The Rocky Mt Tone Bar didn't seem to have quite enuf sustain and felt too light and too short. I tried the Amos but that didn't seem to have quite enuf sustain either, It was too light and it was noisy and scratchy sounding. For my the best weight is around 5 ounces and 3 inches long. I use a lot of Slants and a shorter bar gives me problems, partly because my slants aren't as accurate as they should be. It would help if I was a better player. I am still experimenting.

Nic Neufeld · From: Kansas City, Missouri

I know when I started out I was using the Brozophonic bullet, which is on the smaller side...then I went to a larger Ezee-Slide (similar to the other thermoplastic ones, a really nice slide) and at first I didn't like the size...reverse slants in particular were harder for me...enough that I eventually ordered a smaller one from Basil. But I think that was user error...eventually I preferred the original larger one and that's my main bar.

Rereading your question "I'm also curious if any of you found the heavier bars more difficult to use at first, but persevered with them until they became easy to jump around the neck with."

Yep, I guess that was exactly my experience! Started out disliking the larger bar and ended up preferring it over time.
_________________
Waikīkī, at night when the shadows are falling
I hear the rolling surf calling
Calling and calling to me

Tim Whitlock · From: Colorado, USA

Most any bar will give an acceptable tone and sustain, for me anyway. My priorities are comfort, maneuverability and quiet on the strings. The Clinesmith bar checks all these boxes and it sounds great too. It would be hard to go back to a slow, noisy metal bar. I prefer the 7/8" for the right grip and 3" to cover eight strings.

Tom Snook · From: Ft. Lauderdale, Florida, USA

Bill,would you consider selling 🤔 one of your bars?
Aloha
_________________
I wanna go back to my little grass shack........

Bill McCloskey · From: Nanuet, NY

Everything depends on tuning. If you are playing 6 strings (or even 8 strings) you are going to have to move the bar a lot. lighter, faster better. If you are with pedals or a 10 or 12 string tuning like Alkire or Reece's ext C6, you are going to move the bar less. There for, more weight, the more mass, the better for that tone which you can't get on a bar with less mass.
_________________
Rose D13 tuning: Cabinet by J.R. Rose with mechanics engineered by Darvin Willhoite.
Williams D10 9x9.
Mullen Pre-RP D10 8x5.

Rick Aiello · From: Berryville, VA USA

I received one of Bill Groner's bars ... 2 3/4" x 3/4" ...

I love it ... the conical indent on the back side is marvelous ... a perfect fit for my thumb (reverse slants) ...

Plus it looks really cool with the black tip on the white bar ....

Most excellent ... Cool

Tom Snook · From: Ft. Lauderdale, Florida, USA

I'm going with an Ernie Ball bar,$16.99. Right now I'm using the only bar I own, a Dunlop 919.Its the same bar I took lessons from Jerry Byrd with back in the early 90s,but arthritis is making it difficult to handle so I figure bigger is better
Aloha
_________________
I wanna go back to my little grass shack........

Forum Index > Steel Without Pedals		Next oldest topic :: Next newest topic

All times are GMT - 8 Hours	Jump to: