Tone Bar Selection: Small/lighter vs. Large/heavier
Moderator: Brad Bechtel
- David DeLoach
- Posts: 447
- Joined: 9 Feb 2016 8:27 am
- Location: Tennessee, USA
- Contact:
Tone Bar Selection: Small/lighter vs. Large/heavier
I have a few tone bars but my go-to to is the Dunlap 919 (4.5 oz. - 3/4" x 2-3/4"). I like it for the maneuverability the smaller/lighter bar has.
But I find a larger/heavier bar such as the Dunlap 921 (11.5 oz. - 1" x 3-3/4") gives me a better tone and sustain.
I recently got a Clinesmith thermoplastic tone bar (4.5 oz. - 3/4" x 3") that I really like. Less noise and very easy to move around with.
I'm curious what you guys are using.
I'm also curious if any of you found the heavier bars more difficult to use at first, but persevered with them until they became easy to jump around the neck with.
But I find a larger/heavier bar such as the Dunlap 921 (11.5 oz. - 1" x 3-3/4") gives me a better tone and sustain.
I recently got a Clinesmith thermoplastic tone bar (4.5 oz. - 3/4" x 3") that I really like. Less noise and very easy to move around with.
I'm curious what you guys are using.
I'm also curious if any of you found the heavier bars more difficult to use at first, but persevered with them until they became easy to jump around the neck with.
-
- Posts: 816
- Joined: 4 Oct 2019 7:47 am
- Location: California, USA
I've got a pile about like you do, and I use them all occasionally, but right now I'm really loving a glass 3" x 1" made by Silica Sound, it's big but only has a brass slug in the middle so it's quite a bit lighter than my stainless ZB of the same size. I've been finding the 1" bars way easier to hold.
- Bill Groner
- Posts: 1234
- Joined: 30 Dec 2016 8:42 am
- Location: QUAKERTOWN, PA
- Cody Farwell
- Posts: 95
- Joined: 12 Nov 2018 3:01 pm
- Location: Sunland, CA
- Contact:
- Bill Groner
- Posts: 1234
- Joined: 30 Dec 2016 8:42 am
- Location: QUAKERTOWN, PA
- Rick Aiello
- Posts: 4701
- Joined: 11 Sep 2000 12:01 am
- Location: Berryville, VA USA
- Contact:
- Jack Hanson
- Posts: 5024
- Joined: 19 Jun 2012 3:42 pm
- Location: San Luis Valley, USA
I too have so many tone bars I likely couldn't count 'em, and if I put 'em all in a bucket I probably couldn't lift it. But for years, my go-to bar has been the standard stainless Latch Lake (formerly Broz-O-Phonic) 3/4" x 3" bar from Eagan, MN.
https://latchlakemusic.com/slides/hawaiian-bar/
https://latchlakemusic.com/slides/hawaiian-bar/
-
- Posts: 129
- Joined: 12 Aug 2021 1:18 pm
- Location: South Dakota, USA
I have tried several on my 8 string Rukavina lapsteel. Of the three Dunlop bars I tried I like the 918 the best. Not too short or too heavy. The Rocky Mt Tone Bar didn't seem to have quite enuf sustain and felt too light and too short. I tried the Amos but that didn't seem to have quite enuf sustain either, It was too light and it was noisy and scratchy sounding. For my the best weight is around 5 ounces and 3 inches long. I use a lot of Slants and a shorter bar gives me problems, partly because my slants aren't as accurate as they should be. It would help if I was a better player. I am still experimenting.
- Nic Neufeld
- Posts: 1319
- Joined: 25 Sep 2017 8:10 am
- Location: Kansas City, Missouri
I know when I started out I was using the Brozophonic bullet, which is on the smaller side...then I went to a larger Ezee-Slide (similar to the other thermoplastic ones, a really nice slide) and at first I didn't like the size...reverse slants in particular were harder for me...enough that I eventually ordered a smaller one from Basil. But I think that was user error...eventually I preferred the original larger one and that's my main bar.
Rereading your question "I'm also curious if any of you found the heavier bars more difficult to use at first, but persevered with them until they became easy to jump around the neck with."
Yep, I guess that was exactly my experience! Started out disliking the larger bar and ended up preferring it over time.
Rereading your question "I'm also curious if any of you found the heavier bars more difficult to use at first, but persevered with them until they became easy to jump around the neck with."
Yep, I guess that was exactly my experience! Started out disliking the larger bar and ended up preferring it over time.
Waikīkī, at night when the shadows are falling
I hear the rolling surf calling
Calling and calling to me
I hear the rolling surf calling
Calling and calling to me
- Tim Whitlock
- Posts: 1768
- Joined: 3 Jan 2001 1:01 am
- Location: Colorado, USA
Most any bar will give an acceptable tone and sustain, for me anyway. My priorities are comfort, maneuverability and quiet on the strings. The Clinesmith bar checks all these boxes and it sounds great too. It would be hard to go back to a slow, noisy metal bar. I prefer the 7/8" for the right grip and 3" to cover eight strings.
-
- Posts: 6877
- Joined: 5 Jan 2005 1:01 am
- Location: Nanuet, NY
- Contact:
Everything depends on tuning. If you are playing 6 strings (or even 8 strings) you are going to have to move the bar a lot. lighter, faster better. If you are with pedals or a 10 or 12 string tuning like Alkire or Reece's ext C6, you are going to move the bar less. There for, more weight, the more mass, the better for that tone which you can't get on a bar with less mass.
Check out my latest video: My Biggest Fears Learning Steel at 68: https://youtu.be/F601J515oGc
- Rick Aiello
- Posts: 4701
- Joined: 11 Sep 2000 12:01 am
- Location: Berryville, VA USA
- Contact: