The Steel Guitar Forum Store 

Post new topic Picks
Reply to topic
Author Topic:  Picks
Clark Doughty


From:
KANSAS
Post  Posted 19 Aug 2020 2:22 pm    
Reply with quote

I'M CURRENTLY USING DUNLOP 0.20 PICKS. IS THAT ABOUT AS CLOSE TO THE OLD JEFF NEWMAN DIAMON D AS I CAN GET TODAY?
View user's profile Send private message Send e-mail

Jerry Overstreet


From:
Louisville Ky
Post  Posted 19 Aug 2020 2:32 pm    
Reply with quote

JF Diamond Rings are a little heavier at about .026.
View user's profile Send private message Send e-mail

Clark Doughty


From:
KANSAS
Post  Posted 19 Aug 2020 3:23 pm     Picks
Reply with quote

I HAVE SOME DUNLOP .025'S THAT SHOULD DO THE TRICK. THANKS JERRY
View user's profile Send private message Send e-mail

Jerry Overstreet


From:
Louisville Ky
Post  Posted 19 Aug 2020 3:57 pm    
Reply with quote

You are quite welcome sir.
View user's profile Send private message Send e-mail

Richard Lotspeich

 

From:
North Georgia
Post  Posted 19 Aug 2020 5:28 pm    
Reply with quote

National NP2. Same pick,round holes,and not pre-bent.
_________________
Dick Lotspeich
View user's profile Send private message Send e-mail

Justin Emmert

 

From:
Greensboro, NC
Post  Posted 19 Aug 2020 7:48 pm    
Reply with quote

National NP 2
View user's profile Send private message Send e-mail

Gene Tani


From:
Pac NW
Post  Posted 20 Aug 2020 4:57 am    
Reply with quote

There's premium priced copies of the prewar Nationals made by Showcase 41, Hoffmeyer, Yates etc

But best to start w/brass (easiest) or nickel silver (not stainless) NP2's and shaping the blade by pressing a 8mm hex wrench wrapped in duct tape into the back of the blade on a soft (carpeted) surface
_________________
- keyless Sonny Jenkins laps stay in tune forever!; Carter PSG
- The secret sauce: polyester sweatpants to buff your picks, cheapo Presonus channel strip for preamp/EQ/compress/limiter, Diet Mountain Dew


Last edited by Gene Tani on 20 Aug 2020 5:59 pm; edited 1 time in total
View user's profile Send private message Send e-mail

Richard Lotspeich

 

From:
North Georgia
Post  Posted 20 Aug 2020 11:31 am    
Reply with quote

The "rub" on JF vs NP2 seems to be the blade shape. Im thinking of making a die for the blade bend. Fran told me "she" bent every one sold by hand. I have some new ones to go by,but not so sure they are all the same through the years. I also noticed NP2s went up to 16 bucks for 2 pair.
_________________
Dick Lotspeich
View user's profile Send private message Send e-mail

Ian Rae


From:
Redditch, England
Post  Posted 20 Aug 2020 4:16 pm    
Reply with quote

I shape the NP2s using round-nosed pliers.
Patience required, but a good result.
_________________
Make sleeping dogs tell the truth!
Homebuilt keyless U12 7x5, Excel keyless U12 8x8, Williams keyless U12 7x8, Telonics rack and 15" cabs
View user's profile Send private message Send e-mail Visit poster's website

Gene Tani


From:
Pac NW
Post  Posted 20 Aug 2020 5:57 pm    
Reply with quote

Ian Rae wrote:
I shape the NP2s using round-nosed pliers.
Patience required, but a good result.


Yes, really useful for lots of things, get these at craft/hobby/fabric stores or jewelers supply stores, wrap in duct tape /vinyl tubing:



_________________
- keyless Sonny Jenkins laps stay in tune forever!; Carter PSG
- The secret sauce: polyester sweatpants to buff your picks, cheapo Presonus channel strip for preamp/EQ/compress/limiter, Diet Mountain Dew
View user's profile Send private message Send e-mail

Bobby D. Jones

 

From:
West Virginia, USA
Post  Posted 20 Aug 2020 6:51 pm    
Reply with quote

I
The best way I have found after fixing many sets is, smooth edges an curl wrappers out slightly, Then a drill bit slightly smaller than your index finger and a small ballpein hammer. By pecking the wrappers and moving it around the drill bit you can make a smooth contour with no catching sharp bends. My Right middle finger has damage and bends toward my index finger, If the wrappers have sharp bends the pick catch on each other and pulls 1 of them off.


That piece inside my thumb pick is a little piece of 3M stair safety tape, I have been using it for years and no thumb pick slip.
View user's profile Send private message Send e-mail

Gene Tani


From:
Pac NW
Post  Posted 21 Aug 2020 11:45 pm    
Reply with quote

Making picks in bulk (including shaping blade with pliers)

http://www.deanhoffmeyer.com/nationalpicks/hutchens.html
_________________
- keyless Sonny Jenkins laps stay in tune forever!; Carter PSG
- The secret sauce: polyester sweatpants to buff your picks, cheapo Presonus channel strip for preamp/EQ/compress/limiter, Diet Mountain Dew
View user's profile Send private message Send e-mail

Clark Doughty


From:
KANSAS
Post  Posted 22 Aug 2020 1:53 pm     picks
Reply with quote

GENE,
ATE THE PICKS YOU'RE TALKING ABOUT IN THE ARTICLE ABOVE THE NATIONAL NP2'S? THANKS CLARK
View user's profile Send private message Send e-mail

Gene Tani


From:
Pac NW
Post  Posted 22 Aug 2020 2:48 pm    
Reply with quote

Clark: no, they're called Little Roy's Own, they look different from vintage Nationals, if you do a Control-F on this page for "banjo pick" that's them

https://littleroyandlizzy.com/product
_________________
- keyless Sonny Jenkins laps stay in tune forever!; Carter PSG
- The secret sauce: polyester sweatpants to buff your picks, cheapo Presonus channel strip for preamp/EQ/compress/limiter, Diet Mountain Dew
View user's profile Send private message Send e-mail


All times are GMT - 8 Hours
Jump to:  

Our Online Catalog
Strings, CDs, instruction,
steel guitars & accessories

www.SteelGuitarShopper.com

Please review our Forum Rules and Policies

Steel Guitar Forum LLC
PO Box 237
Mount Horeb, WI 53572 USA


Click Here to Send a Donation

Email admin@steelguitarforum.com for technical support.


BIAB Styles
Ray Price Shuffles for
Band-in-a-Box

by Jim Baron
HTTP