Sho Bud rack and barrel adjustments-balancing G#s on E9
Moderator: Shoshanah Marohn
- Dave Zirbel
- Posts: 4170
- Joined: 4 Aug 1998 11:00 pm
- Location: Sebastopol, CA USA
Sho Bud rack and barrel adjustments-balancing G#s on E9
Hi folks. I have an old crossover that looks terrible but sounds amazing. I've had a few ShoBuds in the last 25 years but never really had a rack and barrel. I love everything about that system except when engaging my B pedal (G#'s to A) the high note has a much quicker response and the low one, and that messes me up a bit since my current steels have balanced pulls. Are there any tricks to improving or getting the pull a little more balanced with switching to a wound 6th (G#) string?
Thank you
Dave
Thank you
Dave
Dave Zirbel-
Sierra S-10 (Built by Ross Shafer),ZB, Fender 400 guitars, various tube and SS amps
Sierra S-10 (Built by Ross Shafer),ZB, Fender 400 guitars, various tube and SS amps
-
- Posts: 3009
- Joined: 1 Dec 1998 1:01 am
- Location: LA,CA
That's the chink in r&b's armor. Maybe there's some trick to lessen it, but I'm not aware of any.
Not sure a wound 6th (22w?) would help, since it's still going to be the 3rd string that needs the most travel, so whatever you have on the 6th will still engage later.
It's just something you have to deal with when you play rack & barrel.
Not sure a wound 6th (22w?) would help, since it's still going to be the 3rd string that needs the most travel, so whatever you have on the 6th will still engage later.
It's just something you have to deal with when you play rack & barrel.
- Paul Malta
- Posts: 16
- Joined: 19 Oct 2016 11:57 am
- Location: New York, USA
Have you looked at the barrel on the rod for that string? They can get stuck and not allow a fine tune of the rod. I would check the barrels for both rods on that pedal. I have a '73 Bud that works perfectly but it took a while for me to get the hang of setting up the barrels so that they function properly. I learned a lot about this by searching the forum for "rack and barrel"... Lots of great stuff written about it and how to troubleshoot and tune it.
Good luck, gotta love those old Buds!
Good luck, gotta love those old Buds!
I wonder if Sid might make a 22W with a core of 10 and a wind of 6. That would react closer to the same. The problem is that if you have a 20P and a 12P both pulling the same pitch, the 20 has much less far to go.
If you switch to a normal 22W, you'll have the other problem, since it's most likely to have a core of 8 and a wind of 7.. Core size determines how much travel you need (and a plain string is all core).
Since you can't time pulls on that guitar, you'll have to get used to it. Some people regard the notchiness as part of the mojo of the older units, kinda like feeling the secondaries open up on a 4 barrel carb, a sensation missing in a fuel injected motor.
I keep meaning to ask Sid (of Live Steel Strings) about the feasibility of a 22LC (Large Core) string to get the faster response. I play a 12 third string, but I bet the throws would be easier to balance with the bigger core.
If you switch to a normal 22W, you'll have the other problem, since it's most likely to have a core of 8 and a wind of 7.. Core size determines how much travel you need (and a plain string is all core).
Since you can't time pulls on that guitar, you'll have to get used to it. Some people regard the notchiness as part of the mojo of the older units, kinda like feeling the secondaries open up on a 4 barrel carb, a sensation missing in a fuel injected motor.
I keep meaning to ask Sid (of Live Steel Strings) about the feasibility of a 22LC (Large Core) string to get the faster response. I play a 12 third string, but I bet the throws would be easier to balance with the bigger core.
2 pedal steels, a lapStrat, and an 8-string Dobro (and 3 ukes)
More amps than guitars, and not many effects
More amps than guitars, and not many effects
- Dave Zirbel
- Posts: 4170
- Joined: 4 Aug 1998 11:00 pm
- Location: Sebastopol, CA USA
- Paul Malta
- Posts: 16
- Joined: 19 Oct 2016 11:57 am
- Location: New York, USA
- Paul Malta
- Posts: 16
- Joined: 19 Oct 2016 11:57 am
- Location: New York, USA
- Ricky Davis
- Posts: 10964
- Joined: 4 Aug 1998 11:00 pm
- Location: Bertram, Texas USA
- Contact:
Use a .012p for the 3rd string and a .022w Nickle for the 6th string. Tighten the lower return spring; all the way tight for the 3rd string. Loosen the lower return spring as much as you can for the 6th string so it barely doesn't move.
Make sure the pedal rod for the 3rd string is connected to the ball in the closest hole to pedal bar and 6th being furthest.
That may get them really really close to pull together; and make sure you are using Jagwire Strings; as they have the best consistent tension for much longer time and take the less amount of tension to pull same gauge string as other brands.
Ricky
Make sure the pedal rod for the 3rd string is connected to the ball in the closest hole to pedal bar and 6th being furthest.
That may get them really really close to pull together; and make sure you are using Jagwire Strings; as they have the best consistent tension for much longer time and take the less amount of tension to pull same gauge string as other brands.
Ricky
Ricky Davis
Email Ricky: sshawaiian2362@gmail.com
Email Ricky: sshawaiian2362@gmail.com
- Dave Zirbel
- Posts: 4170
- Joined: 4 Aug 1998 11:00 pm
- Location: Sebastopol, CA USA
-
- Posts: 3942
- Joined: 23 Dec 2005 1:01 am
- Location: Maryland, USA
I don't understand this part of your post. Not sure what parts you're referring to. (I've never dealt with a rack-and-barrel; I'm familiar with two-hole puller and barrel.)Ricky Davis wrote:Make sure the pedal rod for the 3rd string is connected to the ball in the closest hole to pedal bar and 6th being furthest.
- Ian Worley
- Posts: 2119
- Joined: 14 Jan 2012 12:02 pm
- Location: Sacramento, CA
Dave, you can place a spring on the rod between the rack and the barrel to force string 6 to engage sooner. You give up the ability to tune the pull easily from the end plate though, will require you to reach underneath to adjust that barrel. You also need to flip the rack around backwards (open side toward changer) and place a small flat washer that moves freely but fits fairly snugly around the rod against the rack to keep the spring from feeding into the oblong hole in the rack. You'll have to experiment a little to get the right length and weight spring, but they are readily available at any hardware store.
- Ricky Davis
- Posts: 10964
- Joined: 4 Aug 1998 11:00 pm
- Location: Bertram, Texas USA
- Contact:
Brint;
sorry, forget the pedal rod thing, both strings are on the same pedal...
.duh....ha
sorry, forget the pedal rod thing, both strings are on the same pedal...
.duh....ha
Last edited by Ricky Davis on 14 Feb 2017 1:59 pm, edited 1 time in total.
Ricky Davis
Email Ricky: sshawaiian2362@gmail.com
Email Ricky: sshawaiian2362@gmail.com
- Ian Worley
- Posts: 2119
- Joined: 14 Jan 2012 12:02 pm
- Location: Sacramento, CA
- Ricky Davis
- Posts: 10964
- Joined: 4 Aug 1998 11:00 pm
- Location: Bertram, Texas USA
- Contact:
Oops sorry, my brain injury got in the way, yes forget the pedal rod thing, both strings are on same pedal...ha...duh.
Ricky Davis
Email Ricky: sshawaiian2362@gmail.com
Email Ricky: sshawaiian2362@gmail.com
- Ricky Davis
- Posts: 10964
- Joined: 4 Aug 1998 11:00 pm
- Location: Bertram, Texas USA
- Contact:
But also leave raise spring on 3rd string and take off raise spring for 6th.
Ricky
Ricky
Ricky Davis
Email Ricky: sshawaiian2362@gmail.com
Email Ricky: sshawaiian2362@gmail.com
- Andy DePaule
- Posts: 2576
- Joined: 20 Jun 1999 12:01 am
- Location: Saigon, Viet Nam & Springfield, Oregon
- Contact:
Rig it up?
Far as I know you can't get them to move together because the high G# needs a longer pull and the other very little.
If you really want that to happen I have an untried idea how you can rig it up.
You really have to struggle to think of what to to on the 6 pedals with the E9th tuning.
Leave the High G# barrel where it is and put the lower G# on the rack for pedal 5 or 6.
Then rig up some funky rod and spring to pull from your B pedal rack and yank the rack with the lower G# on it.
Then you can take out most of the slack.
I've had many rack and barrel Sho Buds and even a Mullen with that.
That issue never bothered me once.
Well that my 2¢ worth, Just send a check if you use the idea.
If you really want that to happen I have an untried idea how you can rig it up.
You really have to struggle to think of what to to on the 6 pedals with the E9th tuning.
Leave the High G# barrel where it is and put the lower G# on the rack for pedal 5 or 6.
Then rig up some funky rod and spring to pull from your B pedal rack and yank the rack with the lower G# on it.
Then you can take out most of the slack.
I've had many rack and barrel Sho Buds and even a Mullen with that.
That issue never bothered me once.
Well that my 2¢ worth, Just send a check if you use the idea.
Last edited by Andy DePaule on 14 Feb 2017 5:15 pm, edited 2 times in total.
Inlaid Star Guitar 2006 by Mark Giles. SD-10 4+5 in E9th; http://luthiersupply.com/instrument-gallery.html
2017 Mullen SD-10, G2 5&5 Polished Aluminum covering. Custom Build for me. Great Steel.
Clinesmith Joaquin Murphy style Aluminum 8 String Lap Steel Short A6th.
Magnatone Jeweltone Series Lap Steel, Circa 1950? 6 String with F#minor7th Tuning.
1956 Dewey Kendrick D-8 4&3, Restoration Project.
1973 Sho~Bud Green SD-10 4&5 PSG, Restoration Project.
2017 Mullen SD-10, G2 5&5 Polished Aluminum covering. Custom Build for me. Great Steel.
Clinesmith Joaquin Murphy style Aluminum 8 String Lap Steel Short A6th.
Magnatone Jeweltone Series Lap Steel, Circa 1950? 6 String with F#minor7th Tuning.
1956 Dewey Kendrick D-8 4&3, Restoration Project.
1973 Sho~Bud Green SD-10 4&5 PSG, Restoration Project.
-
- Posts: 3009
- Joined: 1 Dec 1998 1:01 am
- Location: LA,CA
- Dave Zirbel
- Posts: 4170
- Joined: 4 Aug 1998 11:00 pm
- Location: Sebastopol, CA USA
Well I can relate to guitar mojo and will possible learn to live with it, but I did rig up a solution if anyone is interested. I took a rod with a nylon tuner on the end and bent it so the raise rod would go through the lower rack of the B pedal. I spun the rack around and shoved a brass locking barrel inside so now the high G# pulls to the A note quicker....still not perfect but improved. The problem now if that the C pedal has a way longer throw than the B pedal. I got the idea from Tom Bradshaw.
Dave Zirbel-
Sierra S-10 (Built by Ross Shafer),ZB, Fender 400 guitars, various tube and SS amps
Sierra S-10 (Built by Ross Shafer),ZB, Fender 400 guitars, various tube and SS amps