dirty amp

Billy Henderson · Post by **Billy Henderson** » 18 Nov 2015 10:58 am

How do I clean the tolex on my amps? They are not too bad but they do have dust on them.

Erv Niehaus · Post by **Erv Niehaus** » 18 Nov 2015 11:24 am

ArmorAll

Bill A. Moore · Post by **Bill A. Moore** » 18 Nov 2015 12:38 pm

Clean water, and a brush, use sponge after brushing the dirt out of the crevices, and change water often. After drying, use some type of protectant, (I use a Turtle Wax product), to give it a shine.

Gary Cosden · Post by **Gary Cosden** » 18 Nov 2015 1:50 pm

I cleaned up my 1982 NV 400 when the chassis was off to Peavey for repair. I used Dawn and a scrubbing brush and hosed it off and then towel dried it. Next day I felt it looked so much like new that Armor All would have made it look worse. After a few years it's still looking almost like new. Armor All looks fake and shiny in my IMHO.

William Hughes · Post by **William Hughes** » 18 Nov 2015 7:07 pm

Tuff Stuff cleaner and a toothbrush

Bill Hatcher · Post by **Bill Hatcher** » 18 Nov 2015 7:43 pm

NO ARMOUR ALL!~!!!!! thats a mess and when you touch it you cant hold a pic or a bar for the slick crap on your fingers. i wont even buy a used fender amp with that junk on it. yuk!!!

Lane Gray · Post by **Lane Gray** » 19 Nov 2015 2:46 am

Those newish (about a year or so on the market) "magic dirt erasers" work wonders.

John Billings · Post by **John Billings** » 21 Nov 2015 9:26 am

I use a brush cuz of the Tolex texture, and lots of paper towels. To finish it off I use Meguiar's Natural Shine Protectant, "Non-greasy formula cleans, shines & protects." Much nicer than Armor All!

Jack Hanson · Post by **Jack Hanson** » 21 Nov 2015 3:09 pm

I have a book by Texas tube amp guru Gerald Weber in which he recommends pulling the chassis, reverb tank, etc. out of the cabinet and bringing it to a high pressure car wash for a good spray and rinse and then letting the cab sit outside in direct sunlight to dry for however long it takes.

Have never tried this myself, but Mr. Weber likely knows of what he speaks.

John Billings · Post by **John Billings** » 21 Nov 2015 3:12 pm

Weber's method presents one problem for me. I don't want to get the wood and glue joints wet. His method may be quick, and most times effective, but, as a wood worker, I have a real problem with getting wood wet.

chris ivey · Post by **chris ivey** » 21 Nov 2015 3:56 pm

frankly, armour all works great for a quick wipe to clean up an amp or a dashboard.
i actually like funky looking amps that get used.

it will make your motorcycle seat slippery, though.

Donny Hinson · Post by **Donny Hinson** » 22 Nov 2015 8:05 am

Scrub brush and water with a little detergent or soap in it. In a pinch, you can also use Windex. I like to finish dry with a turkish towel, as it gets into the crevices better than paper towels.

Bill Hatcher's right, save the Armor-All stuff for shining your tires!

John Billings · Post by **John Billings** » 22 Nov 2015 8:09 am

Be careful if you use Windex. If there's a scratch with wood showing, the Windex will dye the wood blue. Windex does have a new product that uses Vinegar instead ofAmmonia, and it's clear. Also NEVER use anything that contains Ammonia on anything Aluminum.

Joe Naylor · Post by **Joe Naylor** » 22 Nov 2015 9:53 am

NO ARMOUR ALL! for me either. Just use vinyl cleaner you get at Ace, auto parts store, etc and a paper towel

cleans it right up and does not leave an oily mess

Keep it easy tolex is not magic it is just vinyl

Joe Naylor
www.steelseat.com

The Steel Guitar Forum

dirty amp

dirty amp

Best Tolex Cleaner

my idea