Pedal steel u finish new photo of peda stop an travel stop

Johnie King · Post by **Johnie King** » 2 Aug 2015 7:56 am

[/b]

Johnie King · Post by **Johnie King** » 2 Aug 2015 7:59 am

Good project for you .Double neck all maple cabinet with 10 pedal set up an all the knees u can dream up. Cabinet top measures one half inch thick also front an back apron 1/2 inch this is very close to Emmons cabinet specks. You can email me for more details. zkinglapsteel@gmail.com

Johnie King · Post by **Johnie King** » 2 Aug 2015 8:00 am

Rick Baker · Post by **Rick Baker** » 2 Aug 2015 8:41 am

Price?

Johnie King · Post by **Johnie King** » 2 Aug 2015 9:16 am

Johnie King · Post by **Johnie King** » 2 Aug 2015 9:27 am

Body milled front an back to install steel plate,even with cabinet aprons this adds strength to cabinet an makes for neater appearance. Cross bars use a sliding spring loaded pin in each end . Has Delrin bearing surface at all friction points.

Jeremy Drawbaugh · Post by **Jeremy Drawbaugh** » 2 Aug 2015 1:06 pm

I have a friend who may just very well be interested in this.

Stephen Kerley · Post by **Stephen Kerley** » 2 Aug 2015 1:31 pm

I'm looking for a cabinet. If you will contact me, We can discuss the details. My name is Steve. CELL: 423-208-4686 or stevek0925@aol.com

Johnie King · Post by **Johnie King** » 3 Aug 2015 5:52 am

Johnie King · Post by **Johnie King** » 3 Aug 2015 5:59 am

Cabinet measures 32 - 5/8 long By 10-1/2 wide

Johnie King · Post by **Johnie King** » 11 Aug 2015 12:45 pm

Dark green Formica finish over maple cabinet with polished aluminum strips. Installed flush with Formica . Dark spots is shadows off camera. For price contact zkinglapsteel@gmail.com

Johnie King · Post by **Johnie King** » 7 Sep 2015 7:46 am

Johnie King · Post by **Johnie King** » 14 Oct 2015 1:20 pm

Price $275.00

Johnie King · Post by **Johnie King** » 29 Jan 2016 9:33 am

Bump for lower price $240

Johnie King · Post by **Johnie King** » 31 Jan 2016 11:29 am

Johnie King · Post by **Johnie King** » 31 Jan 2016 11:36 am

Cross bars are standard 3/8,s square and can be removed by pushing on spring loaded pins. Set up for up to 10 pedals an all the knee levers you want. Would make nice double ten.

Steven Black · Post by **Steven Black** » 8 Feb 2016 1:31 pm

Hello Johnie, is this Body still available? need address to send bank check or postal money order, I am interested.

Jim Horan · Post by **Jim Horan** » 8 Feb 2016 6:00 pm

This looks like a very nice body, but where would you ever find end plates for it. It would have to be a keeper, because it is hard to sell a No name Steel

Steven Black · Post by **Steven Black** » 8 Feb 2016 6:29 pm

Hello Jim,I have endplates that will fit this body, but seller does not seem interested in selling this guitar body.

Tony Glassman · Post by **Tony Glassman** » 8 Feb 2016 6:39 pm

Nice job on the spring-loaded cross-shafts. Much easier shaft removal than the LeGrande system (or lack thereof)

Erv Niehaus · Post by **Erv Niehaus** » 9 Feb 2016 8:39 am

Are the cross shafts hollow?

Steven Black · Post by **Steven Black** » 9 Feb 2016 3:34 pm

Hello Erv,yes these cross shafts are hollow.

The Steel Guitar Forum

Pedal steel u finish new photo of peda stop an travel stop

Pedal steel u finish new photo of peda stop an travel stop

Psg

Maple Cabinet

A question from Steve Black

D-10 body

Steel guitar body

Reply from Steve to Erv