MSA Blue Prints?
Moderator: Shoshanah Marohn
- Wayne Neal
- Posts: 62
- Joined: 27 Nov 2013 9:44 am
- Location: Ohio, USA
MSA Blue Prints?
Is there any place to get a set of plans for an MSA sd10 classic? I have some end plates, pedals, cross rods, bell cranks, neck and headstock. Was wondering the specs of the under carraige. I may give building a guitar a try.
D10 Carter, b-bender Tele, Electric Fiddle & Mandolin, Peavey Stereo Chorus 400 BW1203's, Peavey Special 130 Ken Fox mod BW1203.
-
- Posts: 1901
- Joined: 29 Aug 1998 12:01 am
- Location: Waterbury Ctr. VT 05677 USA
- Wayne Neal
- Posts: 62
- Joined: 27 Nov 2013 9:44 am
- Location: Ohio, USA
-
- Posts: 1901
- Joined: 29 Aug 1998 12:01 am
- Location: Waterbury Ctr. VT 05677 USA
I have a 12, but the length should be the same, since they used the same keyheads. And mine is half-disassembled. Let me know what numbers you need. Longitudinal numbers should be the same, but lateral numbers won't.
2 pedal steels, a lapStrat, and an 8-string Dobro (and 3 ukes)
More amps than guitars, and not many effects
More amps than guitars, and not many effects
-
- Posts: 5
- Joined: 6 Feb 2009 5:06 pm
- Location: Ohio, USA
Re: MSA Blue Prints?
I have a SD10 body ,white micaWayne Neal wrote:Is there any place to get a set of plans for an MSA sd10 classic? I have some end plates, pedals, cross rods, bell cranks, neck and headstock. Was wondering the specs of the under carraige. I may give building a guitar a try.
solid maple not plywood!!
Jerry Queen 740-667-9724
Coolville ohio
- Wayne Neal
- Posts: 62
- Joined: 27 Nov 2013 9:44 am
- Location: Ohio, USA
Thanks for the offer Jerry...I have The stuff to build my body already...I am looking for the measurements of stock used to support the underside. Sizes of set screws(for pedal stops etc.) What size to cut the hole to let my changers set in.
I was just fishing I guess to see if any one had done one before or knew where to find such a thing.(Like an exploded veiw of the guitar) I am going to use the back neck off of mine anyhow so I guess when I get time I'll strip down the whole thing-make the measurements-and give it a good cleaning while I'm in the misery
Thanks guys.
I was just fishing I guess to see if any one had done one before or knew where to find such a thing.(Like an exploded veiw of the guitar) I am going to use the back neck off of mine anyhow so I guess when I get time I'll strip down the whole thing-make the measurements-and give it a good cleaning while I'm in the misery
Thanks guys.
D10 Carter, b-bender Tele, Electric Fiddle & Mandolin, Peavey Stereo Chorus 400 BW1203's, Peavey Special 130 Ken Fox mod BW1203.
It appears that the front and rear aprons were drilled on a jig, and not a lot of stuff attached to the wood. I'll be home Sunday. I know you'll need
Height off the deck to the centers of screw holes
Distances between pedal shafts
Distances between pedal shafts and knee lever shafts (they're NOT in the center)
Apron thickness
Apron length
Dimensions and locations of changer holes, also of keyhead mounting holes
Height off the deck of the flat bar on front apron that holds the pedal pull tabs and pedal stops
I can get the rear apron numbers for the *KR hardware, but I'm not a fan of their system
Height off the deck to the centers of screw holes
Distances between pedal shafts
Distances between pedal shafts and knee lever shafts (they're NOT in the center)
Apron thickness
Apron length
Dimensions and locations of changer holes, also of keyhead mounting holes
Height off the deck of the flat bar on front apron that holds the pedal pull tabs and pedal stops
I can get the rear apron numbers for the *KR hardware, but I'm not a fan of their system
2 pedal steels, a lapStrat, and an 8-string Dobro (and 3 ukes)
More amps than guitars, and not many effects
More amps than guitars, and not many effects
- Wayne Neal
- Posts: 62
- Joined: 27 Nov 2013 9:44 am
- Location: Ohio, USA
-
- Posts: 77
- Joined: 23 Dec 2008 4:38 pm
- Location: Tennessee, USA
Msa
Wayne, I am getting a D10 classic that I will be doing a complete cleaning, changers out, all pull rods and bellcranks out, I might be able to help you with any screw sizes or measurment, I should have it apart in about a week.
- Wayne Neal
- Posts: 62
- Joined: 27 Nov 2013 9:44 am
- Location: Ohio, USA