1st String to G#
Moderator: Shoshanah Marohn
1st String to G#
Hi Everyone,
Got my "new" Franklin yesterday and all is going well except that I cannot get the 1st string to pull all the way to G#. Have tried the normal fixes...change string from 12 to 14 (that made it worse) and increased lever travel to the max.
It appears that the finger is at it's maximum travel when I try the pull.
I have it on my RKR along with the 2nd string raise which is no problem at all.
Any ideas would be appreciated.
Thanks in advance.
Mark T.
Got my "new" Franklin yesterday and all is going well except that I cannot get the 1st string to pull all the way to G#. Have tried the normal fixes...change string from 12 to 14 (that made it worse) and increased lever travel to the max.
It appears that the finger is at it's maximum travel when I try the pull.
I have it on my RKR along with the 2nd string raise which is no problem at all.
Any ideas would be appreciated.
Thanks in advance.
Mark T.
- Jerry Overstreet
- Posts: 12622
- Joined: 11 Jul 2000 12:01 am
- Location: Louisville Ky
Hey Mark, yes you definitely need a 12 for a first string. I don't remember exactly the Franklin is configured but you need to put the pull rod for #1 in the bellcrank hole furthest from the guitar body and the changer end use the hole nearest the topside or pick-up side of the guitar. If this is too much angle, you may need to bend a rod..and of course you need to adjust your knee lever stop to accomodate the long travel needed to pull that string up a whole tone. Both of my guitars require this much leverage for this pull..yours may not so you could try the bottom hole in the raise changer end but most have to use the top one.
Hope this helps. JO
You might just try adjusting the stop first...before you go to the trouble of changing the pull rod position.
The Franklins definitely are the ones that know about this change so it any guitar can do it, it has to be this one.
<FONT SIZE=1 COLOR="#8e236b"><p align=CENTER>[This message was edited by Jerry Overstreet on 02 November 2002 at 04:41 AM.]</p></FONT><FONT SIZE=1 COLOR="#8e236b"><p align=CENTER>[This message was edited by Jerry Overstreet on 02 November 2002 at 04:45 AM.]</p></FONT>
Hope this helps. JO
You might just try adjusting the stop first...before you go to the trouble of changing the pull rod position.
The Franklins definitely are the ones that know about this change so it any guitar can do it, it has to be this one.
<FONT SIZE=1 COLOR="#8e236b"><p align=CENTER>[This message was edited by Jerry Overstreet on 02 November 2002 at 04:41 AM.]</p></FONT><FONT SIZE=1 COLOR="#8e236b"><p align=CENTER>[This message was edited by Jerry Overstreet on 02 November 2002 at 04:45 AM.]</p></FONT>
- Bill Moore
- Posts: 2099
- Joined: 5 Jun 2000 12:01 am
- Location: Manchester, Michigan
Like Jerry says, the holes at the changer each are capable of different amounts of travel. The hole nearest the top of the guitar, gives you the least amount of travel, the third one down, gives the most. I think that's the hole you need to connect the rod to. Take a look at which hole is used for the 2nd string raise, it's probably the third one. I have a .013 on my Carter and raise it to G# with no problem. Carter has charts on their web page which give good information on this subject.
------------------
Bill Moore...
my steel guitar web page
<FONT SIZE=1 COLOR="#8e236b"><p align=CENTER>[This message was edited by Bill Moore on 02 November 2002 at 05:43 AM.]</p></FONT>
------------------
Bill Moore...
my steel guitar web page
<FONT SIZE=1 COLOR="#8e236b"><p align=CENTER>[This message was edited by Bill Moore on 02 November 2002 at 05:43 AM.]</p></FONT>
Thanks for the help everyone. I am down to a 10 and am soooooo close but not quite there. My main problem is that everything is maxed out. Top slot in changer,,,,bottom slot in bell crank, full pedal travel.
Don't want to go any lighter than a ten if I can avoid it.
Willing to listen to all ideas.
regards and thanks to all.
mark T.
Don't want to go any lighter than a ten if I can avoid it.
Willing to listen to all ideas.
regards and thanks to all.
mark T.
-
- Posts: 345
- Joined: 7 Jan 1999 1:01 am
- Location: Tallahassee,FL USA
Mark, The only thing I can think of is the lowering return spring not holding the lowering finger of the changer on the rest when the raise is attempted. Make sure the raise finger is the only part of the changer leaving the stop. If the lowering finger is moving on the raise, an adjustment of the return spring is required. Don't over tighten the spring. Tighten just enough to keep the lowering finger on the rest when the raise is attempted. If this is not the cause of the problem, a phone call to Mr. Franklin would be in order.
Good Luck, Leon
Good Luck, Leon
- Jerry Roller
- Posts: 10319
- Joined: 17 Apr 1999 12:01 am
- Location: Van Buren, Arkansas USA
- Contact:
Mark, I would suggest you put a .012 string back on the guitar, then back the raise nylon tuner completely off until the string does not raise at all. Then tighten the lower return spring about 4 to 6 turns if there is an adjustment which I am almost sure there is. Now start tuning the nylon tuner as you activate the lever and it should pull to G# with ease. I think the pull is overpowering the lower return spring and you might have overtuned while trying to compensate for the weak spring tension. After you do this you may need to reduce some of the travel if you have it set to the max.
Jerry
Jerry
- Jerry Roller
- Posts: 10319
- Joined: 17 Apr 1999 12:01 am
- Location: Van Buren, Arkansas USA
- Contact:
Hey Mark,
Jerry & Leon hit it right on the head.
I had the same problem with my old
Professional.
Tightened the lowering finger return spring
so it held back that part while trying to
raise up to G# and that did the trick!
<font face=loosiescript><FONT SIZE=1 COLOR="#8e236b"><p align=CENTER>[This message was edited by Jay Ganz on 02 November 2002 at 08:30 AM.]</p></FONT>
Jerry & Leon hit it right on the head.
I had the same problem with my old
Professional.
Tightened the lowering finger return spring
so it held back that part while trying to
raise up to G# and that did the trick!
<font face=loosiescript><FONT SIZE=1 COLOR="#8e236b"><p align=CENTER>[This message was edited by Jay Ganz on 02 November 2002 at 08:30 AM.]</p></FONT>
- Bill Ferguson
- Posts: 5692
- Joined: 4 Aug 1998 11:00 pm
- Location: Milton, FL USA
- Contact:
-
- Posts: 6437
- Joined: 2 Dec 1999 1:01 am
- Location: Upstate SC.
I wanted to thank everyone for all the help. With a 0.10 I can get it to work. The twelve did not work at all. Not sure what is going on but there probably is some defect in the changer that I can't see. There was a lot of junk in it, which I removed with a can of compressed air.
Perhaps there is the unkown fuzz ball lurking
Thanks again and I will gladly try any other ideas.
Regards,
Mark T.
Perhaps there is the unkown fuzz ball lurking
Thanks again and I will gladly try any other ideas.
Regards,
Mark T.
-
- Posts: 156
- Joined: 4 Aug 1998 11:00 pm
- Location: Suisun City, CA USA
-
- Posts: 6437
- Joined: 2 Dec 1999 1:01 am
- Location: Upstate SC.
Mark if this an old guitar, and I get the feeling it is.Tighten the lower return spring all the way down.Sometimes these springs can go bad.If it still doesn't pull to pitch even with a .013, and the changer is clear of broken strings etc.Try another spring.If you don't have one.Borrow one from say the 8th string on C6th.Chances are it's not had much use and should be in good shape.Hope this helps!---------bb
I just wanted to thank everyone for the help. It was a change problem but cured. The finger was hitting the wood cutout for the changer on the body and while there was enough travel to get the string to a G, the finger was not getting the full amount of travel that is possible. That has been fixed and while there is more travel, I do suspect that the return spring is not working up to full strength. Will remedy that later.
What a great group...
Thanks
Mark T.
What a great group...
Thanks
Mark T.
-
- Posts: 1990
- Joined: 6 Jul 2001 12:01 am
- Location: Denham Springs, LA
-
- Posts: 6437
- Joined: 2 Dec 1999 1:01 am
- Location: Upstate SC.
I wouldn't want to be playing it when it did break. Ouch that's gotta hurt.
Anyone ever broke the 4th and the 5th strings simultaneously? I've been playing for 30 years.I had this happen twice within a 2 year period.I know what you're thinking.But the guitar did not malfunction.(Over pull)It happened on 2 different guitars.It was just one of those strange things that can happen.I just about lost the bar both times.But I some how held on.Kinda scared me though. <FONT SIZE=1 COLOR="#8e236b"><p align=CENTER>[This message was edited by Bobby Boggs on 09 November 2002 at 08:28 AM.]</p></FONT>
Anyone ever broke the 4th and the 5th strings simultaneously? I've been playing for 30 years.I had this happen twice within a 2 year period.I know what you're thinking.But the guitar did not malfunction.(Over pull)It happened on 2 different guitars.It was just one of those strange things that can happen.I just about lost the bar both times.But I some how held on.Kinda scared me though. <FONT SIZE=1 COLOR="#8e236b"><p align=CENTER>[This message was edited by Bobby Boggs on 09 November 2002 at 08:28 AM.]</p></FONT>