how to replace pot in ernie ball vol pedal
Moderator: Shoshanah Marohn
- Terry Pendlay
- Posts: 287
- Joined: 22 Aug 2005 12:01 am
- Location: Effingham Illinois, USA
how to replace pot in ernie ball vol pedal
can anyone help with step by step details on how to replace a pot in a ernie ball model 6166 vol. pedal. i have not done this before and do not want mess it up . thanks Terry
-
- Posts: 1435
- Joined: 12 Jun 1999 12:01 am
- Location: Portland, OR
Terry,
I think they are basically all the same, if you have a digital camera, take pictures as you go..also look at Gregg's website.
Bill
http://www.gregcutshaw.com/Goodrich%201 ... 20Pot.html
I think they are basically all the same, if you have a digital camera, take pictures as you go..also look at Gregg's website.
Bill
http://www.gregcutshaw.com/Goodrich%201 ... 20Pot.html
Bill Ford S12 CLR, S12 Lamar keyless, Misc amps&toys Sharp Covers
Steeling for Jesus now!!!
Steeling for Jesus now!!!
- Jerry Overstreet
- Posts: 12622
- Joined: 11 Jul 2000 12:01 am
- Location: Louisville Ky
All the EB's I have worked on are a bit different from the Goodrich and others far as string routing in particular is concerned. The Goodrich, Fender and sho-bud diagrams won't help you there.
I have a diagram somewhere, but can't find it at the moment. Perhaps someone else will have one.
The string routes through nearly the entire space of the inside area. They use a spring to connect the string together and keep tension on it also.
They used to have a tute and some info on their site www.ernieball.com but I don't see it now. They would also install the pot with new string, spring and a basic o'haul for a reasonble fee.
It ain't all that difficult actually... as mentioned, you just need to make notes and rewire the new pot just like the old one. Same with the string.
As I recall, the pot mount can be removed from the pedal make the installation somewhat easier.
It can be a tad tedious, but personally I find it easier than the Goodrich. JMO. Best of Luck
I have a diagram somewhere, but can't find it at the moment. Perhaps someone else will have one.
The string routes through nearly the entire space of the inside area. They use a spring to connect the string together and keep tension on it also.
They used to have a tute and some info on their site www.ernieball.com but I don't see it now. They would also install the pot with new string, spring and a basic o'haul for a reasonble fee.
It ain't all that difficult actually... as mentioned, you just need to make notes and rewire the new pot just like the old one. Same with the string.
As I recall, the pot mount can be removed from the pedal make the installation somewhat easier.
It can be a tad tedious, but personally I find it easier than the Goodrich. JMO. Best of Luck
Sonny Morris sjm227@hotmail.com
- Dick Sexton
- Posts: 3554
- Joined: 2 Oct 2006 12:01 am
- Location: Greenville, Ohio
- Contact:
Pedal Repair/Rebuild
Ernie Ball has a repair service for all of their pedals. They claim, good as new after the rebuild. Here is a link to the F.A.Q with details and cost..
http://www.ernieball.com/faq_content.ph ... vol_pedals
http://www.ernieball.com/faq_content.ph ... vol_pedals
- Jerry Overstreet
- Posts: 12622
- Joined: 11 Jul 2000 12:01 am
- Location: Louisville Ky
- Scott Swartz
- Posts: 1038
- Joined: 23 Jan 2001 1:01 am
- Location: St. Louis, MO
- Contact:
I use the Ernie Ball pedal exclusively, and I find it is much easier to remove the two philips screws for the pot mount bracket as Jerry suggests. This allows you to hook the string without having to fight the spring tension. Once the string is hooked, you pull the pot mount back into place and insert the screws.